Part 2
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
INSTRUMENT PANEL ASSEMBLY
CLUSTER LID C
Removal
1. Pull instrument finisher E backward by approximately 30 degrees while disengaging the metal clips and pawl.
2. Remove screws.
3. Pull back, and disengage pawls and metal clips.
4. Disconnect harness connector, and then remove cluster lid C.
Installation
Installation is in the reverse order of removal.
COMBINATION METER
Removal
1. Pull instrument finisher E backward by approximately 30 degrees while disengaging the metal clips and pawl.
2. Remove front pillar garnish. Component.
3. Pull up instrument side panel and disengage pawls.
Broken Circle Indicates Pawl
4. Remove instrument side panel.
5. Insert a remover into upper space of instrument mask.
Broken Circle Indicates Pawl
6. Disengage pawls, and then remove instrument side mask.
7. Insert a remover into space of instrument side finisher.
8. Disengage metal clips, and then remove instrument side finisher.
9. Insert suitable tool into the bottom gap of side ventilator assembly after removing the instrument side mask, push against A and
B as shown to disengage the pawls.
Broken Circle Indicates Pawl
10. Lift the side ventilator up from the bottom, pull backward while disengaging the side ventilator assembly's upper pawls, and then remove the side ventilator.
Broken Circle Indicates Pawl
11. Remove screws, and disengage pawls.
12. Remove steering column cover upper.
13. Remove screws from instrument upper panel right side.
14. Lift the instrument upper panel up, disengage metal clips.
15. Pull backward and disengage clips.
16. Remove cluster lid A.
17. Remove screws (A) and metal clip (B), and remove combination meter.
Installation
Installation is in the reverse order of removal.
GLOVE BOX ASSEMBLY
Removal
1. Remove glove box screws.
2. Pull backward while disengaging the glove box assembly pawls.
3. Remove glove box assembly.
Installation
Installation is in the reverse order of removal.
INSTRUMENT LOWER FINISHER
Removal
1. Pull backward while disengage the instrument lower finisher's clip and pawls.
Broken Square Indicates Metal Clip
2. Disconnect in-vehicle sensor and harness connector, and then remove instrument lower finisher.
Installation
Installation is in the reverse order of removal.
CENTER CONSOLE ASSEMBLY
Removal
1. Insert a suitable tool into front side space of console mask, and disengage metal clips.
Broken Square Indicates Metal Clip
2. Disconnect harness connector, and then remove console mask.
3. Place the shift lever in "D" position (A/T and CVT only).
Broken Square Indicates Metal Clip
4. Remove shift lever handle (A/T and CVT only). (CVT), Removal And Installation (A/T).
5. Pull up and disengage A/T and CVT console finisher metal clips
(A/T and CVT only).
6. Remove A/T and CVT console finisher (A/T and CVT only).
7. Remove shift lever handle (M/T only). .
8. Pull up and disengage M/T console boot metal clips (M/T only).
9. Remove M/T console boot (M/T only).
10. Disengage console rear finisher metal clips and pawl.
11. Remove console rear finisher.
12. Disengage console mask cover metal clips and pawls, and then remove console mask cover (with armrest).
13. Disengage rear cup holder metal clips and pawls (without armrest).
14. Remover rear cup holder (without armrest).
15. Remove console body assembly screws and nut.
16. Disconnect harness connector, and then remove console body assembly.
17. Remove both of the instrument lower cover LH and RH clips.
Broken Square Indicates Metal Clip
18. Disengage instrument lower cover LH and RH metal clips and remove both of the instrument lower cover LH and RH.
19. Remove screws and then remove center console.
Installation
Installation is in the reverse order of removal.