Radio and CD Player
DTC U0195: Satellite radio CAN time-out
CAUTION:
If DTC U0195 is set in the radio and CD player, diagnose the CAN main bus line.
CAUTION:
Whenever the radio and CD player is replaced, ensure that the communication circuit is normal.
DIAGNOSTIC FUNCTION
When the signals from satellite radio tuner cannot be received, the radio and CD player sets DTC U0195.
JUDGMENT CRITERIA
With the ignition switch in the ON position, system voltage between 10 - 16 volts (data from ETACS-ECU), power supply fuse(IOD fuse) is OK, or odometer value is 80.5 km (50 miles) or more, and the communications with satellite radio tuner cannot be established for 2,500 ms or more, the radio and CD player determines that a problem has occurred.
TROUBLESHOOTING HINTS
- The CAN bus line may be defective.
- The radio and CD player may be defective.
- The satellite radio tuner may be defective.
DIAGNOSIS
Required Special Tools:
- MB991958: Scan Tool (M.U.T.-III Sub Assembly)
- MB991824: V.C.I.
- MB991827: M.U.T.-III USB Cable
- MB991910: M.U.T.-III Main Harness A
STEP 1. Using scan tool MB991958, diagnose the CAN bus line
(1)
CAUTION:
To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
Connect scan tool MB991958. Refer to "How to connect the Scan Tool (M.U.T.-III) Scan Tool Testing and Procedures."
(2)Turn the ignition switch to the "ON" position.
(3)Diagnose the CAN bus line.
(4)Turn the ignition switch to the "LOCK" (OFF) position.
Q. Is the CAN bus line found to be normal?
YES Go to Step 2.
NO Repair the CAN bus line. CAN Bus Diagnostics Chart).
STEP 2. Using scan tool MB991958 read the satellite radio tuner diagnostic trouble code.
Check whether a satellite radio tuner DTCs are set or not.
(1)Turn the ignition switch to the "ON" position.
(2)Check for satellite radio tuner DTCs.
(3)Turn the ignition switch to the "LOCK" (OFF) position.
Q. Is the DTC set?
YES Diagnose the satellite radio tuner. (Refer to Satellite Radio Tuner.)
NO Go to Step 3.
STEP 3. Using scan tool MB991958, read the SRS-ECU diagnostic trouble code.
Check if the DTC U0195 is set to the SRS-ECU.
Q. Is the DTC set?
YES Go to Step 4.
NO Go to Step 5.
STEP 4. Recheck for diagnostic trouble code.
Check again if the DTC is set to the radio and CD player.
(1)Erase the DTC.
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
(3)Check if DTC is set.
(4)Turn the ignition switch to the "LOCK" (OFF) position.
Q. Is the DTC set?
YES Replace the satellite radio tuner.
NO The trouble can be an intermittent malfunction such as a poor connection or open circuit in the CAN bus lines between the satellite radio tuner and the radio and CD player How to Cope With Intermittent Malfunctions).
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set to the radio and CD player.
(1)Erase the DTC.
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
(3)Check if DTC is set.
(4)Turn the ignition switch to the "LOCK" (OFF) position.
Q. Is the DTC set?
YES Replace the radio and CD player.
NO The trouble can be an intermittent malfunction such as a poor connection or open circuit in the CAN bus lines between the satellite radio tuner and the radio and CD player How to Cope With Intermittent Malfunctions).