Inspection Procedure 2

Inspection Procedure 2: Steering wheel audio remote control switch does not function. [Vehicles with MMCS]

CAUTION:
Before replacing the multivision display, ensure that the power supply circuit, the ground circuit and the communication circuit are normal.














TECHNICAL DESCRIPTION (COMMENT)

The power supply circuit to the steering wheel audio remote control switch, the steering wheel audio remote control switch, the multivision display, or the clock spring may be defective.

TROUBLESHOOTING HINTS

- Malfunction of steering wheel audio remote control switch

- Malfunctions of multivision display

- Malfunction of the clock spring

- Damaged harness wires and connectors

DIAGNOSIS

Required Special Tools:

- MB991223: Harness Set

- MB992006: Extra Fine Probe

STEP 1. Check the remote controlled radio switch.

Check the steering wheel audio remote control switch (Refer to Component Tests and General Diagnostics).

Q. Is the remote controlled radio switch in good condition?

YES Go to Step 2.
NO Replace the remote controlled radio switch.
STEP 2. Check clock spring connector C-204 and C-205 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q. Are clock spring connector C-204 and C-205 in good condition?

YES Go to Step 3.
NO Repair or replace the damaged component Harness Connector Inspection). The steering wheel audio remote control switch should work normally.
STEP 3. Check the clock spring.

Check whether the clock spring is in good condition Driver's Air Bag Module Inspection (Except Ralliart) [Except RALLIART] or Driver's Air Bag Module Inspection (Ralliart) [RALLIART]).

Q. Is the check result normal?

YES Go to Step 4.
NO Replace the clock spring.
STEP 4. Check multivision display connector C-12 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q. Is multivision display connector C-12 in good condition?

YES Go to Step 5.
NO Repair or replace the damaged component Harness Connector Inspection). The steering wheel audio remote control switch should work normally.
STEP 5. Check the wiring harness between multivision display connector C-12 (terminal 53, 69) and clock spring connector C-205 (terminal 2, 3).

- Check the communication lines for open and short circuit.

NOTE:
Also check intermediate connector C-105 for loose, corroded, or damaged terminals, or terminals pushed back in the connector. If intermediate connector C-105 is damaged, repair or replace the connector as described in Harness Connector Inspection Harness Connector Inspection.

Q. Is the wiring harness between multivision display connector C-12 (terminal 53, 69) and clock spring connector C-205 (terminal 2, 3) in good condition?

YES Go to Step 6.
NO The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary.
STEP 6. Check steering wheel audio remote control switch connector C-202 for loose, corroded or damaged terminals, or terminals pushed back in the connector.

Q. Is steering wheel audio remote control switch connector C-202 in good condition?

YES Go to Step 7.
NO Repair or replace the damaged component Harness Connector Inspection). The steering wheel audio remote control switch should work normally.
STEP 7. Check the wiring harness between steering wheel audio remote control switch connector C-202 (terminal 2, 4) and clock spring connector C-204 (terminal 5, 4).

- Check the communication lines for open and short circuit.

Q. Is the wiring harness between steering wheel audio remote control switch connector C-202 (terminal 2, 4) and clock spring connector C-204 (terminal 5, 4) in good condition?

YES
Go to Step 8.

NO The wiring harness may be damaged or the connector(s) may have loose, corroded or damaged terminals, or terminals pushed back in the connector. Repair the wiring harness as necessary.
STEP 8. Retest the system

Check whether you can operate the multivision display by using the steering wheel audio remote control.

Q. Is the check result normal?

YES The trouble can be an intermittent malfunction How to Cope With Intermittent Malfunctions).
NO Replace the multivision display.