Radio and CD Player
DTC U0155: Meter CAN time-out
CAUTION:
If DTC U0155 is set in the radio and CD player, diagnose the CAN main bus line.
CAUTION:
Whenever the radio and CD player is replaced, ensure that the communication circuit is normal.
DIAGNOSTIC FUNCTION
When the signals from combination meter cannot be received, the radio and CD player sets DTC U0155.
JUDGMENT CRITERIA
With the ignition switch in the ON position, system voltage between 10 - 16 volts (data from ETACS-ECU), power supply fuse(IOD fuse) is OK, or odometer value is 80.5 km (50 miles) or more, and the communications with combination meter cannot be established for 2,500 ms or more, the radio and CD player determines that a problem has occurred.
TROUBLESHOOTING HINTS
- The CAN bus line may be defective.
- The radio and CD player may be defective.
- The combination meter may be defective.
DIAGNOSIS
Required Special Tools:
- MB991958: Scan Tool (M.U.T.-III Sub Assembly)
- MB991824: V.C.I.
- MB991827: M.U.T.-III USB Cable
- MB991910: M.U.T.-III Main Harness A
STEP 1. Using scan tool MB991958, diagnose the CAN bus line
(1)
CAUTION:
To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
Connect scan tool MB991958. Refer to "How to connect the Scan Tool (M.U.T.-III) Reading and Clearing Diagnostic Trouble Codes."
(2)Turn the ignition switch to the "ON" position.
(3)Diagnose the CAN bus line.
(4)Turn the ignition switch to the "LOCK" (OFF) position.
Q. Is the CAN bus line found to be normal?
YES Go to Step 2.
NO Repair the CAN bus line. CAN Bus Diagnostics Chart).
STEP 2. Using scan tool MB991958 read the combination meter diagnostic trouble code.
Check whether a combination meter DTCs are set or not.
(1)Turn the ignition switch to the "ON" position.
(2)Check for combination meter DTCs.
(3)Turn the ignition switch to the "LOCK" (OFF) position.
Q. Is the DTC set?
YES Diagnose the combination meter (Refer to combination meter, Diagnosis Combination Meter).
NO Go to Step 3.
STEP 3. Using scan tool MB991958, read the ETACS-ECU diagnostic trouble code.
Check if the DTC U0155 is set to the ETACS-ECU.
Q. Is the DTC set?
YES Go to Step 4.
NO Go to Step 5.
STEP 4. Recheck for diagnostic trouble code.
Check again if the DTC is set to the radio and CD player.
(1)Erase the DTC.
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
(3)Check if DTC is set.
(4)Turn the ignition switch to the "LOCK" (OFF) position.
Q. Is the DTC set?
YES Replace the combination meter.
NO The trouble can be an intermittent malfunction such as a poor connection or open circuit in the CAN bus lines between the combination meter and the radio and CD player How to Cope With Intermittent Malfunctions).
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set to the radio and CD player.
(1)Erase the DTC.
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
(3)Check if DTC is set.
(4)Turn the ignition switch to the "LOCK" (OFF) position.
Q. Is the DTC set?
YES Replace the radio and CD player.
NO The trouble can be an intermittent malfunction such as a poor connection or open circuit in the CAN bus lines between the combination meter and the radio and CD player How to Cope With Intermittent Malfunctions).