MMCS
DTC U0195: Satellite Radio CAN TimeoutCAUTION:
- If DTC U0195 is set in the CAN box unit, diagnose the CAN main bus line.
- Whenever the CAN box unit is replaced, ensure that the communication circuit is normal. (Check that the voltage is 10 V or more.)
DIAGNOSTIC FUNCTION
When the signals from satellite radio tuner cannot be received, the CAN box unit sets DTC U0195.
JUDGMENT CRITERIA
With the ignition switch in the ON position, system voltage between 10 - 16 volts (data from ETACS-ECU), power supply fuse(IOD fuse) is OK, or odometer value is 80.5 km (50 miles) or more, and the communications with satellite radio tuner cannot be established for 2,500 ms or more, the CAN box unit determines that a problem has occurred.
TROUBLESHOOTING HINTS
- The CAN bus line may be defective.
- The CAN box unit may be defective.
- The satellite radio tuner may be defective.
DIAGNOSIS
Required Special Tools:
- MB991958 Scan Tool (M.U.T.-III Sub Assembly)
- MB991824: V.C.I.
- MB991827 M.U.T.-III USB Cable
- MB991910 M.U.T.-III Main Harness A
STEP 1. Using scan tool MB991958, diagnose the CAN bus line
CAUTION: To prevent damage to scan tool MB991958, always turn the ignition switch to the "LOCK" (OFF) position before connecting or disconnecting scan tool MB991958.
1. Connect scan tool MB991958. Refer to "How to connect the Scan Tool (M.U.T.-III)." How to Connect the Scan Tool (M.U.T.-III)
2. Turn the ignition switch to the "ON" position.
3. Diagnose the CAN bus line.
4. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the CAN bus line found to be normal?
YES : Go to Step 2.
NO : Repair the CAN bus line
STEP 2. Using scan tool MB991958 read the satellite radio tuner diagnostic trouble code.
Check whether a satellite radio tuner DTCs are set or not
1. Turn the ignition switch to the "ON" position.
2. Check for satellite radio tuner DTCs.
3. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Diagnose the satellite radio tuner. Diagnostic Trouble Code Descriptions
NO : Go to Step 3.
STEP 3. Using scan tool MB991958, read the SRS-ECU diagnostic trouble code.
Check if the DTC U0195 is set to the SRS-ECU.
Q: Is the DTC set?
YES : Go to Step 4.
NO : Go to Step 5.
STEP 4. Recheck for diagnostic trouble code.
Check again if the DTC is set to the CAN box unit
1. Erase the DTC.
2. Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
3. Check if DTC is set.
4. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the satellite radio tuner.
NO : The trouble can be an intermittent malfunction such as a poor connection or open circuit in the CAN bus lines between the satellite radio tuner and the CAN box unit.
STEP 5. Recheck for diagnostic trouble code.
Check again if the DTC is set to the CAN box unit
1. Erase the DTC.
2. Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
3. Check if DTC is set.
4. Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Replace the CAN box unit.
NO : The trouble can be an intermittent malfunction such as a poor connection or open circuit in the CAN bus lines between the satellite radio tuner and the CAN box unit.