Fastener Tightening Specifications
| Generator and drive belt | Adjusting bolt | 5 +/- 1 Nm |
| Adjusting nut lock bolt | 23 +/- 2 Nm | |
| Camshaft position sensing cylinder bolt | 22 +/- 4 Nm | |
| Camshaft position sensor boolt | 8.8 +/- 1 Nm | |
| Camshaft position sensor support bolt | 14 +/-1 Nm | |
| Crankshaft pulley bolt | 25 +/- 5 Nm | |
| Generator brace bolt | 24 +/- 3 Nm | |
| Generator pivot bolt nut | 44 +/- 10 Nm | |
| Ignition coil bolt | 10 +/- 2 Nm | |
| Spark plugs | 25 +/- 5 Nm | |
| Water pump pulley bolt | 8.8 +/- 1 Nm | |
| Timing belt | Auto-tensioner bolt | 24 +/- 3 Nm |
| Camshaft sprocket bolt | 88 +/- 10 Nm | |
| Counterbalance shaft sprocket bolt | 45 +/- 3 Nm | |
| Crankshaft bolt | 162 +/- 5 Nm | |
| Crankshaft position sensor bolt | 8.8 +/- 1 Nm | |
| Engine support bracket bolt and nut | 49 +/- 5 Nm | |
| Idler pulley bolt | 44 +/- 5 Nm | |
| Oil pump sprocket nut | 35 +/- 6 Nm | |
| Power steering pump bolt | 49 +/- 5 Nm | |
| Tensioner arm bolt | 22 +/- 4 Nm | |
| Tensioner B bolt | 19 +/- 3 Nm | |
| Tensioner pulley bolt | 48 +/- 6 Nm | |
| Timing belt cover flange bolt M6 | 11 +/- 1 Nm | |
| Timing belt cover flange bolt M8 | 14 +/- 1 Nm | |
| Timing belt cover washer assembled bolt | 8.8 +/- 1 Nm | |
| Fuel and emission control parts | EGR valve bolt | 19 +/-3 Nm |
| Fuel pressure regulator bolt | 8.8 +/- 2 Nm | |
| Injectors and fuel rail bolt | 12 +/- 1 Nm | |
| Throttle body bolt | 19 +/- 3 Nm | |
| Throttle body stay bolt | 19 +/- 3 Nm | |
| Water pump and intake manifold | Engine coolant temperature gauge unit | 11 +/- 1 Nm |
| Engine coolant temperature sensor | 29 +/- 10 Nm | |
| Engine hanger bolt | 19 +/- 3 Nm | |
| Intake manifold plenum bolt and nut | 20 +/- 2 Nm | |
| Intake manifold plenum stay M8 | 21 +/- 4 Nm | |
| Intake manifold plenum stay M10 | 30 +/- 3 Nm | |
| Manifold differential pressure sensor bolt | 4.9 +/- 1 Nm | |
| Oil dipstick guide bolt | 14 +/-1 Nm | |
| Thermostat housing bolt | 24 +/-4 Nm | |
| Water inlet fitting bolt | 13 +/- 2 Nm | |
| Water inlet pipe bolt | 13 +/- 2 Nm | |
| Water pump bolt | 14 +/- 1 Nm | |
| Exhaust manifold | Exhaust manifold bracket bolt | 35 +/- 6 Nm |
| Exhaust manifold cover bolt | 14 +/- 1 Nm | |
| Bracket bolt | 35 +/- 6 Nm | |
| Exhaust manifold nut M8 | 29 +/- 3 Nm | |
| Exhaust manifold nut M10 | 49 +/- 5 Nm | |
| Oxygen sensor | 44 +/- 5 Nm | |
| Water outlet fitting bolt | 13 +/- 2 Nm | |
| Rocker arms and camshaft | PCV valve | 10 +/- 2 Nm |
| Rocker cover bolt | 3.5 +/- 0.5 Nm | |
| Rocker arm shaft bolt | 31 +/- 3 Nm | |
| Cylinder head and valve | Cylinder head bolt [Tighten to 78 Nm (58 ft. lbs.) and then completely before tightening to final torque specification] | 25 Nm + 90 deg + 90 deg |
| Front case, counterbalance shaft and oil pan | Drain plug | 39 +/- 5 Nm |
| Flange bolt | 36 +/- 3 Nm | |
| Front case bolt | 24 +/- 3 Nm | |
| Oil filter part number MD360935 | 14 +/- 2 Nm | |
| Oil filter other than MITSUBISHI genuine filter | 17 +/- 2 Nm | |
| Oil filter bracket bolt | 19 +/- 3 Nm | |
| Oil pan bolt | 6.9 +/- 1 Nm | |
| Oil pressure switch | 11 +/- 1 Nm | |
| Oil pump cover bolt | 17 +/- 1 Nm | |
| Oil pump cover screw | 9.8 +/- 2 Nm | |
| Oil screen bolt | 19 +/- 3 Nm | |
| Plug | 24 +/- 3 Nm | |
| Relief plug | 44 +/- 5 Nm | |
| Piston and connecting rod | Connecting rod cap nut | 20 +/- 2 Nm |
| Crankshaft and cylinder block | Bearing cap bolt | 25 +/- 2 Nm + 90 deg |
| Bell housing cover bolt | 8.8 +/- 1 Nm | |
| Drive plate bolt | 132 +/- 5 Nm | |
| Flywheel bolt | 132 +/- 5 Nm | |
| Knock sensor | 23 +/- 2 Nm | |
| Oil seal case bolt | 11 +/- 1 Nm | |
| Rear plate bolt | 11 +/- 1 Nm |