3. No Sound From One Speaker (Continued)

STEP 26. Check the harness wires between door speaker (RH) connector E-01 and amplifier connector D-20.

NOTE: After inspecting intermediate connectors C-19 and C-93, inspect the wire. If intermediate connectors C-19 and C-93 are damaged, repair or replace them. Refer to Harness Connector Inspection.

If the harness wires between door speaker (RH) connector E-01 and amplifier connector D-20 are damaged, repair them.
The door speaker (RH) should sound.

If the harness wires are in good condition, go to Step 27.

STEP 27. Check the DIN cable between amplifier and radio, tape player and CD auto changer.
If the DIN cable between amplifier and radio, tape player and CD auto changer is damaged, repair or replace it. The door speaker (RH) should sound.

If the DIN cable is in good condition, repair or replace the amplifier or radio, tape player and CD auto changer. The door speaker (RH) should sound.




STEP 28. Check the rear speaker (LH).
1. Remove the rear speaker (LH).
2. Check that the rear speaker (LH) generates noise when a five-volt voltage is applied on the rear speaker (LH) terminal.
If the rear speaker (LH) is not generating noise, replace the rear speaker (LH).
The rear speaker (LH) should sound.
If the rear speaker (LH) is generating noise, go to Step 29.







STEP 29. Check rear speaker (LH) connector F-23 and amplifier connector D-20 for damage.
If harness connectors D-20 and F-23 are damaged, repair or replace them. Refer to Harness Connector Inspection.
The rear speaker (LH) should sound.

If harness connectors D-20 and F-23 are in good condition, go to Step 30.













STEP 30. Check the harness wires between rear speaker (LH) connector F-23 and amplifier connector D-20.


NOTE: After inspecting intermediate connectors C-90 and C-93, inspect the wire. If intermediate connectors C-90 and C-93 are damaged, repair or replace them. Refer to Harness Connector Inspection.

If the harness wires between rear speaker (LH) connector F-23 and amplifier connector D-20 are damaged, repair them.
The rear speaker (LH) should sound.

If the harness wires are in good condition, go to Step 31.

STEP 31. Check the DIN cable between amplifier and radio, tape player and CD auto changer.
If the DIN cable between amplifier and radio, tape player and CD auto changer is damaged, repair or replace it. The rear speaker (LH) should sound.

If the DIN cable is in good condition, repair or replace the amplifier or radio, tape player and CD auto changer. The rear speaker (LH) should sound.




STEP 32. Check the rear speaker (RH).
1. Remove the rear speaker (RH).
2. Check that the rear speaker (RH) generates noise when a five-volt voltage is applied on the rear speaker (RH) terminal.
If the rear speaker (RH) is not generating noise, replace the rear speaker (RH).
The rear speaker (RH) should sound.
If the rear speaker (RH) is generating noise, go to Step 33.







STEP 33. Check rear speaker (RH) connector F-19 and amplifier connector D-20 for damage.
If harness connectors D-20 and F-19 are damaged, repair or replace them. Refer to Harness Connector Inspection.
The rear speaker (RH) should sound.

If harness connectors D-20 and F-19 are in good condition, go to Step 34.







STEP 34. Check the harness wire between rear speaker (RH) connector F-19 and audio amplifier connector D-20.
If the harness wire between rear speaker (RH) connector F-19 and amplifier connector D-20 is damaged, repair it. The rear speaker (RH) should sound.

If the harness wire is in good condition, go to Step 35.

STEP 35. Check the DIN cable between amplifier and radio, tape player and CD auto changer.
If the DIN cable between amplifier and radio, tape player and CD auto changer is damaged, repair or replace it. The rear speaker (RH) should sound.

If the DIN cable is in good condition, repair or replace the amplifier or radio, tape player and CD auto changer. The rear speaker (RH) should sound.




STEP 36. Check the center speaker.
1. Remove the center speaker.
2. Check that the center speaker generates noise when a five-volt voltage is applied on the center speaker terminal.
If the center speaker is not generating noise, replace the center speaker.
The center speaker should sound.
If the center speaker is generating noise, go to Step 37.







STEP 37. Check center speaker connector C-08 and amplifier connector D-20 for damage.
If harness connectors C-08 and D-20 are damaged, repair or replace them. Refer to Harness Connector Inspection.
The center speaker should sound.

If harness connectors C-08 and D-20 are in good condition, go to Step 38.










STEP 38. Check the harness wires between center speaker connector C-08 and amplifier connector D-20.

NOTE: After inspecting intermediate connector C-93, inspect the wire. If intermediate connector C-93 is damaged, repair or replace it. Refer to Harness Connector Inspection.

If the harness wires between center speaker connector C-08 and amplifier connector D-20 are damaged, repair them. The center speaker should sound.

If the harness wires are in good condition, go to Step 39.

STEP 39. Check the DIN cable between amplifier and radio, tape player and CD auto changer.
If the DIN cable between amplifier and radio, tape player and CD auto changer is damaged, repair or replace it. The center speaker should sound.

If the DIN cable is in good condition, repair or replace the amplifier or radio, tape player and CD auto changer. The center speaker should sound.




STEP 40. Check the tweeter (LH).
1. Remove the tweeter (LH).
2. Check that the tweeter (LH) generates noise when a five-volt voltage is applied on the tweeter (LH) terminal.
If the tweeter (LH) is not generating noise, replace the tweeter (LH).
The tweeter (LH) should sound.
If the tweeter (LH) is generating noise, go to Step 41.







STEP 41. Check tweeter (LH) connector E-0B and amplifier connector D-20 for damage.
If harness connectors D-20 and E-08 are damaged, repair or replace them. Refer to Harness Connector Inspection.
The tweeter (LH) should sound.

If harness connectors D-20 and E-08 are in good condition, go to Step 42.













STEP 42. Check the harness wires between tweeter (LH) connector E-08 and amplifier connector D-20.

NOTE: After inspecting intermediate connectors C-91 and C-93, inspect the wire. If intermediate connectors C-91 and C-93 are damaged, repair or replace them. Refer to Harness Connector Inspection.

If the harness wires between tweeter (LH) connector E-08 and amplifier connector D-20 are damaged, repair them. The tweeter (LH) should sound.

If the harness wires are in good condition, go to Step 43.

STEP 43. Check the DIN cable between amplifier and radio, tape player and CD auto changer.
If the DIN cable between amplifier and radio, tape player and CD auto changer is damaged, repair or replace it. The tweeter (LH) should sound.

If the DIN cable is in good condition, repair or replace the amplifier or radio, tape player and CD auto changer. The weeter (LH) should sound.




STEP 44. Check the tweeter (RH).
1. Remove the tweeter (RH).
2. Check that the tweeter (RH) generates noise when a five-volt voltage is applied on the tweeter (RH) terminal.
If the tweeter (RH) is not generating noise, replace the tweeter (RH). The tweeter (RH) should sound.
If the tweeter (RH) is generating noise, go to Step 45.







STEP 45. Check tweeter (RH) connector E-03 and amplifier connector D-20 for damage.
If harness connectors D-20 and E-03 are damaged, repair or replace them. Refer to Harness Connector Inspection.
The tweeter (RH) should sound.

If harness connectors D-20 and E-03 are in good condition, go to Step 46.










STEP 46. Check the harness wires between tweeter (RH) connector E-03 and amplifier connector D-20.

NOTE: After inspecting intermediate connectors C-19 and C-93, inspect the wire. If intermediate connectors C-19 and C-93 are damaged, repair or replace them. Refer to Harness Connector Inspection.

If the harness wires between tweeter (RH) connector E-03 and amplifier connector D-20 are damaged, repair them. The tweeter (RH) should sound.

If the harness wires are in good condition, go to Step 47.

STEP 47. Check the DIN cable between amplifier and radio, tape player and CD auto changer.
If the DIN cable between amplifier and radio, tape player and CD auto changer is damaged, repair or replace it. The tweeter (RH) should sound.

If the DIN cable is in good condition, repair or replace the amplifier or radio, tape player and CD auto changer. The tweeter (RH) should sound.