OBD-II Drive Cycle Diagnostic Procedures

1996 thru 199 ECLIPSE 420A Engine OBD II Drive Cycle

The following procedure has been established to assist technicians in the field with enabling and running OBD II Monitors. The order listed in the following procedures is intended to allow the technician to effectively complete each monitor and to set the Readiness Status in the least time possible.

NOTE: - Once the monitor run process has begun, do not turn off the ignition. By turning teh ignition key off the monitor enabling conditions will be lost. Only the O2 Heater Monitor runs after key off.
- By performing a battery disconnect, or erasing daignostic trouble codes, the Readiness and all additional OBD information will be cleared.

Monitor Run Process Tip
The following is an outline of the Monitoring Run Process, including suggestions and tips in order to aid in teh process of meeting the enabling criteria for these monitors. The most efficient order has been outlined below. The first two monitors have very similar enabling critera, so it is possible that the Evaporative Leak Monitor will run while operating the vehicle to enable the Catalyst Monitor.

Evaporative Leak Monitor
This monitor requires a cold start, usually an overnight soak or parked for at least 8 hours without the engine running. The engine coolant temperature must be within 10° of ambient/battery temperature, and the sensed ambient (outside) temperature must be between approximately 40° and 90° F.

Catalyst Monitor
The vehicle will need to be driven at a steady highway speed for a few minutes. The monitor will typically enable and start running around 45 to 60 mph under normal driving conditions. If the vehicle is equipped with a manual transmission, using 4th gear may assist in meeting the monitor running criteria.

EGR Monitor
The EGR monitor enable conditions are basic that the vehicle is in closed loop operation and coolant termpature above 170° F. It is necessary to maintain the TPS, MAP, RPM, and Vehicle Speed ranges at a constant with very little fluctuation to allow the monitor to complete during the cycle.

O2 Sensor Monitor
The vehicle will need to be driven for a period of time at highway speeds and brought to a complete stop for a short period of time, with the Automatic Transaxle left in Drive. The O2 Monitor will not run in Park or Neutral on Automatic Transaxle equipped vehicles.

Purge Monitor
The Purge Free cells must be updated before the monitor will run. The enabling conditions are similar to the O2 Sensor Monitor enabling conditions such as, the vehicle will need to be driven for a period of time at highway speeds and brought to a complete stop. The Purge Flow Monitor will attempt to run every OTHER throttle closure. If all of the parameteres are met and it still does not run, with your foot firmly on the Brake, quickly open and close the throttle. This will allow another Purge Free update, and then the Purge Flow Monitor should run.

O2 Sensor Heater Monitor
The vehicle will need to be driven for a period of time at highway speeds to satisfy the enabling conditions for the O2 Sensor Heater Monitor. The monitor runs with the ignition key off after the vehicle operation. Allow the vehicle to hot soak for a few minutes before checking to determine if the monitor completed the cycle. Turning the key on prematurely will abort the monitor test and the vehicle will have to be driven to arm the enabling conditions again.

Mis-Fire Monitor
Mis-Fire Monitor is continuously running during engine operation. For the Mis-Fire Monitor to be enabled, the Adaptive Numerator must be learned.

Adaptive Numerator
The Adaptive Numerator is a software learning routine that tells the PCM where the crankshaft slots are. Since every crankshaft is different, the PCM must learn exactly where its particular crankshaft slots are; otherwise its RPM calculations would be wrong. After a battery disconnect and then a power-up of the PCM, the Adaptive Numerator is set to a value which it would be at it everything were perfect (crankshaft slots, sensors, PCM hardware, etc.). If the Adapative Numerator is equal to the default value, no learning has happened and the Mis-Fire Monitor will not run. To allow the PCM to learn the Adaptive Numerator, the following must happen:

- Open throttle
- Engine Coolant Temperature above 100° F
- More than 10" of vacuum
- Above 1200 RPM
- Below 3000 (Automatic Transaxles)
- Below 3488 (Manual Transaxles)

Once the PCM has learned the Adapative Numerator, the Mis-Fire Monitor will run.

Fuel System Monitor
Fuel System Monitor is continuously running during engine operation.