Attachment III - Technical Information
OVERVIEWDepending on vehicle and build date, this program will involve installing rain hats onto the door latches inside both front doors and/or installing a piece of polyethylene tape under the belt moulding on the rear doors. Also, all door latches will be greased using a pre-filled, specially marked syringe.
See the chart to determine which operations to perform on the vehicle being serviced.
SERVICE KIT CONTENTS
FRONT DOOR REPAIR - ALL FIVE HUNDRED AND MONTEGO VEHICLES AND CERTAIN FREESTYLE VEHICLES
NOTE:
Freestyle vehicles built from June 21, 2005 through December 14, 2005 do not require rain hat installation. Proceed directly to Door Latch Greasing - All Vehicles in this Attachment III.
DOOR TRIM PANEL REMOVAL
1. Remove the exterior mirror trim cover from the inner door panel, then disconnect the mirror control switch electrical connector.
2. Remove the front door handle bezel screw cover, the screw and then the bezel.
3. Remove the two (2) front door handle trim cover screws.
4. CAUTION: Avoid pulling directly on the upper rear corner (vinyl portion) of the door trim panel during removal to prevent damage to the door trim panel.
Remove the five (5) front door trim panel screws, then gently pull the door panel straight off the door to disengage the retaining clips.
5. Disconnect the power window/door lock switch electrical connector.
6. If equipped with power memory seat, disconnect the power memory seat electrical connector, then remove the front door trim panel from the vehicle.
7. Remove the water shield from the door module oval opening.
RAIN HAT INSTALLATION
1. Reach into the opening to locate and remove the existing door latch cable shield as follows:
a) Lift the shield up off the cable.
b) Disengage the tab from the latch, then remove and discard the shield. See Figure 1.
2. NOTE: The rain hats are embossed with an "L" or an "R" to identify on which side of the vehicle they are to be installed. See Figure 2.
NOTE:
BE SURE TO INSTALL THE PUSHPIN INTO THE RAIN HAT FIRST, then install the rain hat onto the door latch.
Insert the supplied pushpin into the rain hat. See Figure 2.
3. Install the rain hat as follows:
a) Position the rain hat cable hook feature onto the door latch cable. See Figure 3.
b) Lay the rain hat down onto the latch cable and slide the rain hat into position over the latch with the gasketed edges of the rain hat against the door sheet metal. See Figures 4 and 5.
c) Seat the pushpin into the latch. See Figure 5.
DOOR TRIM PANEL INSTALLATION
1. Reinstall the water shield.
2. Reinstall the door trim panel, connecting the power seat memory connector, if equipped, and the power window/door lock switch connectors.
3. Make sure all retaining clips are securely fastened to the door, then reinstall the trim panel screws.
4. Install the front door handle trim cover screws.
5. Install the front door handle bezel, screw and cover.
6. Connect and install the exterior mirror trim cover.
DOOR LATCH GREASING - ALL VEHICLES
NOTE:
This operation is to be performed on all four (4) door latches of all affected vehicles.
NOTE:
A single syringe of latch grease contains enough material for one (1) vehicle. The syringe is marked indicating the amount of grease to be applied to each door latch.
1. Remove the door latch upper screw located toward the outside of the door. See Figure 6.
2. Fully insert the tip of the syringe into the screw hole and apply approximately one (1) unit of grease (one graduation mark on the syringe). See Figure 7.
3. Wipe away any excess grease then reinstall the latch screw. Tighten the screw to 12 Nm (9 lb-ft).
REAR DOOR REPAIR - FREESTYLE ONLY
1. Completely lower both rear windows.
2. Open the rear door and remove the belt moulding screw. See Figure 8.
3. CAUTION: Use care not to bend the moulding during removal. The fastener at the rear end of the moulding will not reattach to the clip on the door if the moulding is bent. Adjust (straighten) the moulding if necessary.
Remove the belt moulding by lifting the back end up first and then working the moulding out of the channel.
4. CAUTION: The surfaces the tape is being affixed to must be clean and dry or the tape will not properly adhere. It will be pushed out of position when the belt moulding is reinstalled and not provide the water protection it Is designed for. Make certain the surface where the tape will be affixed is clean of all contaminants (dirt, dust, grime, tape adhesive residue).
Using a clean rag, wipe the door clean around the rear of the channel.
5. Peel the backing off a piece of supplied polyethylene tape and apply it as follows: See Figure 9.
a) Position the tape so that it covers approximately 20 mm (3/4 in) of the rear of the channel.
b) Position the tape so that it is affixed to the horizontal surface of the rubber trim at the bottom of the glass. keep the tape on the horizontal surface only or it may be visible after the belt moulding is reinstalled.
c) Press the tape firmly into place.
6. Reinstall the moulding by first installing the front end of the moulding in the channel then pushing it down and through the polyethylene tape, then attach the moulding to the clip at the rear of the door. The moulding should sit flush against the door.
7. NOTE: The kit includes only one (1) extra tape strip.
Check to make sure the tape is not visible after the moulding is installed. If it is, remove the moulding and the tape, clean the area of all adhesive residue, then repeat Steps 4 through 7 using the extra piece of tape in the kit. Do not reapply the same piece of tape.
8. Reinstall the belt moulding screw.
9. Perform Steps 2 through 8 on the other rear door.