Passenger Side

SPECIAL TOOL(S)

REMOVAL

NOTE: The driver seat is shown, the passenger seat is similar.

1. Prepare the vehicle for seat control switch removal.
1 Disconnect the battery ground cable and wait at least one minute.

WARNING:
^ TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BACKUP POWER SUPPLY MUST BE DEPLETED BEFORE REPAIRING OR REPLACING ANY FRONT OR SIDE AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) COMPONENTS AND BEFORE SERVICING, REPLACING, ADJUSTING OR STRIKING COMPONENTS NEAR THE FRONT OR SIDE AIR BAG SENSORS, SUCH AS DOORS, INSTRUMENT PANEL, CONSOLE, DOOR LATCHES, STRIKERS, SEATS AND HOOD LATCHES.
^ TO DETERMINE LOCATION OF THE FRONT AIR BAG SENSORS, REFER TO AIR BAG SYSTEMS.
^ THE SIDE AIR BAG SENSORS ARE LOCATED AT OR NEAR THE BASE OF THE B-PILLAR.
^ TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE AND WAIT AT LEAST ONE MINUTE. BE SURE TO DISCONNECT AUXILIARY BATTERIES AND POWER SUPPLIES (IF EQUIPPED).

2 Deactivate the Supplemental Restraint System (SRS) and remove the passenger seat.

WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, READ AND FOLLOW ALL WARNINGS, CAUTIONS, NOTES AND INSTRUCTIONS IN THE SEAT REMOVAL AND INSTALLATION PROCEDURE.

NOTE: The supplemental restraint system (SRS) deactivation and reactivation has been incorporated as part of the seat removal and installation procedure.







2. Disconnect the electrical connectors.
1 Release the tab and disconnect the power seat track electrical connector.
2 Release the tab and disconnect the power pedal electrical connector (if equipped).







3. Remove the recliner handle.







4. Remove the side shield screw.







5. Carefully pull out on the outer side shield releasing the two hidden dips (shown) to the inner side shield and the two hidden clips to the recliner mechanism.







6. Remove the outer side shield.
1 Carefully pull out on the side of the outer side shield releasing the clips to the inner side shield and one hidden clip at the side of the seat cushion frame.
2 Carefully pull forward on the side shield releasing the hidden clip at the front of the seat cushion frame.
3 While routing the wire harness out of the seat cushion frame, slide the side shield forward to clear the recliner handle and remove the outer side shield.







7. Remove the screws and the switch.

INSTALLATION

WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, READ AND FOLLOW ALL WARNINGS, CAUTIONS AND NOTES AT THE BEGINNING OF THE REMOVAL PROCEDURE.

NOTE: The driver seat is shown, the passenger seat is similar.







1. Position the switch and install the screws.







2. Position the inner side shield to the seat.







3. Install the outer side shield to the seat.
1 Position the outer side shield to the seat and push in where indicated to install the retaining clips.

NOTE: Route the power pedal (if equipped) and seat (if equipped) switch wire harnesses through the side of the seat while positioning the outer side shield to the seat.

2 Squeeze the inner and outer side shields together to seat the clips.







4. Install the outer side shield screw.







5. Install the recliner handle.







6. Connect the electrical connectors.
1 Connect the power seat track electrical connector (if equipped).
2 Connect the power pedal electrical connector (if equipped).
7. Restore the vehicle to operating condition.
1 Install the driver seat and reactivate the supplemental restraint system (SRS).

WARNING: TO REDUCE THE RISK OF SERIOUS PERSONAL INJURY, READ AND FOLLOW ALL WARNINGS, CAUTIONS, NOTES AND INSTRUCTIONS IN THE SEAT REMOVAL AND INSTALLATION PROCEDURE.

NOTE: The supplemental restraint system (SRS) deactivation and reactivation has been incorporated as part of the seat removal and installation procedure.

2 With all the restraint system diagnostic tools removed, prove out the supplemental restraint system (SRS).

WARNING: THE RESTRAINT SYSTEM DIAGNOSTIC TOOL IS FOR RESTRAINT SYSTEM SERVICE ONLY. REMOVE FROM THE VEHICLE PRIOR TO ROAD USE. FAILURE TO REMOVE COULD RESULT IN INJURY AND POSSIBLE VIOLATION OF THE VEHICLE SAFETY STANDARDS.

3 Check the active restraint system for correct operation.