Four Wheel Anti-Lock Brake System (4WABS)

DTC SOURCE ACTION

11 Generated by a disturbed or defective GO to DTC 11-1.
redundancy channel.
16 No error codes present If system is
still not
functioning,
REFER to
Symptom Chart.
17 Generated by reference voltage failure, GO to DTC 17-1.
caused by high/low battery voltage, main
power relay, main fuse, wire harness.
18 Generated by open or short circuit-isolation GO to DTC 18-1.
valve #1, wire harness.
19 Generated by open or short circuit-isolation GO to DTC 19-1.
valve #2, wire harness.
22 Generated by open or short circuit-LH front GO to DTC 22-1.
inlet valve, wire harness.
23 Generated by open or short circuit-LH front GO to DTC 23-1.
outlet valve, wire harness.
24 Generated by open or short circuit-RH front GO to DTC 24-1.
inlet valve, wire harness.
25 Generated by open or short circuit-RH front GO to DTC 25-1.
outlet valve, wire harness.
26 Generated by open or short circuit-RH rear GO to DTC 26-1.
inlet valve, wire harness.
27 Generated by open or short circuit-RH rear GO to DTC 27-1.
outlet valve, wire harness.
28 Generated by open or short circuit-LH rear GO to DTC 28-1.
inlet valve, wire harness.
29 Generated by open or short circuit-LH rear GO to DTC 29-1.
outlet valve, wire harness.
31 Generated by open or short circuit-LH front GO to Pinpoint
sensor, wire harness. Test A.
32 Generated by open or short circuit-RH front GO to Pinpoint
sensor, wire harness. Test B.
33 Generated by open or short circuit-RH rear GO to Pinpoint
sensor, wire harness. Test C.
34 Generated by open or short circuit-LH rear GO to Pinpoint
sensor, wire harness. Test D.
35 Generated by open or short circuit LH front GO to Pinpoint
sensor, wire harness, damaged teeth on Test A.
indicator ring, sensor air gap too small
/large.
36 Generated by open or short circuit RH front GO to Pinpoint
sensor, wire harness, damaged teeth on Test B.
indicator ring, sensor air gap too small
/large.
37 Generated by open or short circuit RH rear GO to Pinpoint
sensor, wire harness, damaged teeth on Test C.
indicator ring, sensor air gap too small
/large.
38 Generated by open or short circuit LH rear GO to Pinpoint
sensor, wire harness, damaged teeth on Test D.
indicator ring, sensor air gap too small
/large.
41 Generated by missing sensor signal LH front GO to Pinpoint
sensor (missing indicator ring). Test A.
42 Generated by missing sensor signal RH front GO to Pinpoint
sensor (missing indicator ring). Test B.
43 Generated by missing sensor signal RH rear GO to Pinpoint
sensor (missing indicator ring). Test C.
44 Generated by missing sensor signal LH rear GO to Pinpoint
sensor (missing indicator ring). Test D.
55 Generated by missing sensor signal LH front GO to Pinpoint
sensor (long term failure). Test A.
56 Generated by missing sensor signal RH front GO to Pinpoint
sensor (long term failure). Test B.
57 Generated by missing sensor signal RH rear GO to Pinpoint
sensor (long term failure). Test C.
58 Generated by missing sensor signal LH rear GO to Pinpoint
sensor (long term failure). Test D.
61 Generated by short circuit to ground-FLS #2 GO to Pinpoint
or wire harness. Test E.
62 Generated by short circuit to ground-pedal GO to Pinpoint
travel switch or wire harness. Test E.
63 Generated by no pump motor speed sensor GO to DTC 63-1.
signal during initial check @ 31 km/h (19
mph), wire harness.
64 Generated by pump unable to build pressure GO to DTC 64-1.
during an ABS stop.
67 Generated by pump motor running not triggered GO to DTC 67-1.
by anti-lock brake control module.
75 Generated by intermittent missing LH front GO to Pinpoint
sensor signal at speeds < 40 km/h (25 Test A.
mph).
76 Generated by intermittent missing RH front GO to Pinpoint
sensor signal at speeds < 40 km/h (25 Test B.
mph).
77 Generated by intermittent missing RH rear GO to Pinpoint
sensor signal at speeds < 40 km/h (25 Test C.
mph).
78 Generated by intermittent missing LH rear GO to Pinpoint
sensor signal at speeds < 40 km/h (25 Test D.
mph).