FREE REPAIR MANUALS & LABOR GUIDES 1982-2013 Vehicles
Courtesy of Operation CHARM: Car repair manuals for everyone.
Home >> Mercedes Benz >> 2012 >> C 300 4MATIC (204.081) V6-3.0L (272.948) >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> Manufacturer Code Charts >> 1306

Manufacturer Code Charts: 1306


Component Y10/1 (Power steering pump pressure regulator valve) has a short circuit to ground.


Possible cause:

- Y10/1 (Power steering pump pressure regulator valve)
- N10/1kI (Circuit 87 relay, engine)
- N10/1f57 (Fuse 57)
Affected functions:

- Steering Function

-------------------------------------------------

Test 1: Check power supply of component N3/10 (ME-SFI [ME] control unit).

Test 2: Arrangement of fuses

Test 3: Check component Y10/1 (Power steering pump pressure regulator valve).

1. Check power supply of component N3/10 (ME-SFI [ME] control unit).

Test 1.1: Test voltage supply of circuit 87.

Test 1.2: Test current consumption of component N10/1kR (Circuit 87 relay, engine).

Test 1.3: Test voltage supply of circuit 15.

Test 1.4: Test voltage supply of circuit 87. ( Check using actual value )

Test 1.5: Test voltage supply of circuit 30.

1.1. Test voltage supply of circuit 87.
Connect socket box to component N3/10 (ME-SFI [ME] control unit).
Figure legend

- A -ConnectionTest cable 35-pin socket box
- 001 -Sockets of component N3/10 (ME-SFI [ME] control unit)
- 05 -35-pin socket box
- 050 -126-pin socket box
- 108 -Test cable 266 589 01 63 00
- N3/10 (ME-SFI [ME] control unit)
- II 1-63ConnectionTest cable
- III 64-126ConnectionTest cable
Warning!

-
- Connection A of test cable 108 may NOT be connected to connection B of the 126-pin socket box (050).
Continue to test with button F2







Test voltage supply of circuit 87.
Test sequence

- Measure direct voltage with multimeter between sockets [ F.2 ] 98 and [F.3] 99 of the 126-pole socket box tester.
- Measure direct voltage with multimeter between sockets [ F.4 ] 100 and [ F.5 ] 101 of the 126-pole socket box tester.
- Measure direct voltage with multimeter between sockets [ F.6 ] 102 and [ F.5 ] 101 of the 126-pole socket box tester.
- Switch on ignition.
Specified value

- Voltage[11.0...15.0] V
Question

- Are the measurement values OK?


YES
The measurement values are OK.Further possible causes of fault

- Test voltage supply of circuit 30.


NO
The measurement values are not OK.Possible cause and remedy

- N10/1f43 (Fuse 43)
- N10/1f44 (Fuse 44)
- N10/1kI (Circuit 87 relay, engine)
- Lines
- N10/1 (Driver-side SAM control unit with fuse and relay module)
End of test







1.2. Test current consumption of component N10/1kR (Circuit 87 relay, engine).
Connect socket box to component N3/10 (ME-SFI [ME] control unit).
Figure legend

- A -ConnectionTest cable 35-pin socket box
- 001 -Sockets of component N3/10 (ME-SFI [ME] control unit)
- 05 -35-pin socket box
- 050 -126-pin socket box
- 108 -Test cable 266 589 01 63 00
- N3/10 (ME-SFI [ME] control unit)
- II 1-63ConnectionTest cable
- III 64-126ConnectionTest cable
Warning!

-
- Connection A of test cable 108 may NOT be connected to connection B of the 126-pin socket box (050).
Continue to test with button F2







Test current consumption of component N10/1kR (Circuit 87 relay, engine).
Test sequence

- Measure direct current with multimeter between sockets [F.4] 100 and [F.27] 123 of the 126-pole socket box tester.
- Switch on ignition.
Specified value

- Amperage[0.1...0.3] A
Question

- Is the measurement value OK?


YES
The test was okay.End of test

NO
The measurement value is not OK.Possible cause and remedy

- Lines to component N10/1kR (Circuit 87 relay, engine)
- N10/1kR (Circuit 87 relay, engine)
End of test

1.3. Test voltage supply of circuit 15.
Connect socket box to component N3/10 (ME-SFI [ME] control unit).
Figure legend

- A -ConnectionTest cable 35-pin socket box
- 001 -Sockets of component N3/10 (ME-SFI [ME] control unit)
- 05 -35-pin socket box
- 050 -126-pin socket box
- 108 -Test cable 266 589 01 63 00
- N3/10 (ME-SFI [ME] control unit)
- II 1-63ConnectionTest cable
- III 64-126ConnectionTest cable
Warning!

-
- Connection A of test cable 108 may NOT be connected to connection B of the 126-pin socket box (050).
Continue to test with button F2







Test voltage supply of circuit 15.
Test sequence

- Measure direct voltage with multimeter between sockets [ F.2 ] 98 and [ F.15 ] 111 of the 35-pole socket box tester.
- Switch on ignition.
Specified value

- Voltage[11.0...15.0] V
Question

- Is the measurement value OK?


YES
The measurement value is OK.End of test

NO
The measurement value is not OK.Possible cause and remedy

- N10/1f52 (Fuse 52)
- Lines
End of test







1.4. Test voltage supply of circuit 87. ( Check using actual value )
Test prerequisite

- The voltage test at component G1 (Battery) is o.k.
- Ignition ON
Status of relevant actual value:
- Battery voltage:Warning! Communication with ECU required.
Specified value

- Battery voltage[11.0 ... 15.0] V
Question:Is the actual value o.k.?

YES
The actual value is okay.End of test

NO
The actual value is not o.k.Possible cause and remedy

- Test voltage supply of circuit 30.
- Test voltage supply of circuit 87.


1.5. Test voltage supply of circuit 30.
Connect socket box to component N3/10 (ME-SFI [ME] control unit).
Figure legend

- A -ConnectionTest cable 35-pin socket box
- 001 -Sockets of component N3/10 (ME-SFI [ME] control unit)
- 05 -35-pin socket box
- 050 -126-pin socket box
- 108 -Test cable 266 589 01 63 00
- N3/10 (ME-SFI [ME] control unit)
- II 1-63ConnectionTest cable
- III 64-126ConnectionTest cable
Warning!

-
- Connection A of test cable 108 may NOT be connected to connection B of the 126-pin socket box (050).
Continue to test with button F2







Test voltage supply of circuit 30.
Test sequence

- Measure direct voltage with multimeter between sockets [ F.2 ] 98 and [ F.16 ] 112 of the 35-pole socket box tester.
- Switch on ignition.
Specified value

- Voltage[11.0...15.0] V
Question

- Is the measurement value OK?


YES
The measurement value is OK.End of test

NO
The measurement value is not OK.Possible cause and remedy

- F34f42 (Fuse 42)
- Lines
End of test







2. Arrangement of fuses
Figure legend/figure

- N10/1 (Driver-side SAM control unit with fuse and relay module)
Fuses

- FuseF43-F67
Relays

- I =N10/1kI (Circuit 87 relay, engine)
- K =N10/1kK (Circuit 87 relay, chassis)
- L =N10/1kL (Starter relay)
- M =N10/1kM (SEQ [ASG] pump control relay)
- N =N10/1kN (Circuit 15 relay)
- O =N10/1kO (FAN relay module)
- P =N10/1kP (Circuit 15R relay)
- R =N10/1kR (Air pump or oil cooler fan relay)







3. Check component Y10/1 (Power steering pump pressure regulator valve).
Figure legend

- A -ConnectionTest cable 35-pin socket box
- 001 -Sockets of component N3/10 (ME-SFI [ME] control unit)
- 05 -35-pin socket box
- 050 -126-pin socket box
- 108 -Test cable 266 589 01 63 00
- N3/10 (ME-SFI [ME] control unit)
- II 1-63ConnectionTest cable
- III 64-126ConnectionTest cable
Warning!

- Connection A of test cable 108 may NOT be connected to connection B of the 126-pin socket box (050).
Continue to test with button F2







Test sequence

- Switch off ignition.
- Connect socket box (126-pin) to component N3/10 (ME-SFI [ME] control unit).
- Measure direct current with multimeter between sockets [F.4] 100 and [M.5] 5 of the 126-pole socket box tester.
- Switch on ignition.
Specified value

- Amperage [1.5...2.2] A
Question

- Is the measurement value OK?


YES
The measurement value is OK.Possible cause and remedy

- In the event of stored faults with a high fault frequency count or in the event of customer complaints, check lines and connectors for loose contact and corrosion..
End of test

NO
The measurement value is not OK.Possible cause and remedy

- N10/1f54 (Fuse 54)
- Check line from control module N3/10 (ME-SFI [ME] control unit) to component Y10/1 (Power steering pump pressure regulator valve).
- Y10/1 (Power steering pump pressure regulator valve)
End of test

pro multis Credits:Operation CHARM About Operation CHARM