Transmission Control Module Codes
ETC2 (722.9) [7-Gear] as of 2005
DTC TEST SCOPE
0218 Temperature of gear oil is too high.�
0604 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
0605 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
0607 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
060C Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
0613 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
061B The internal engine torque computation performed in component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is faulty.�
062F Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
0633 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
0641 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
0642 The voltage supply of the speed sensors is faulty. ( Undervoltage )�
0643 The voltage supply of the speed sensors is faulty. ( Overvoltage )�
0701 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
0705 Component Y3/8s1 (Selection range sensor (VGS)) is defective.�
0706 Check component Y3/8s1 (Selection range sensor (VGS)).�
0712 The signal from component Y3/8s2 (Transmission oil temperature sensor (VGS)) is implausible. ( Undervoltage )�
0713 The signal from component Y3/8s2 (Transmission oil temperature sensor (VGS)) is implausible. ( Overvoltage )�
0716 The transmission input shaft has rotated at excessive rpms.�
0717 The signal from component Y3/8n1 (Turbine speed sensor (VGS)) is not available.�
0718 Component Y3/8n1 (Turbine speed sensor (VGS)) is defective.�
0720 Mechanical fault of component Drive train�
0721 The transmission output speed signal is implausible when compared to the wheel rpm signal.�
0722 The signal from component Y3/8n3 (Output speed sensor (VGS)) is not available.�
0723 Component Y3/8n3 (Output speed sensor (VGS)) is defective.�
0741 Actuation of torque converter lockup clutch is not possible.�
0742 Engaging of torque converter lockup clutch not permitted.�
0748 The internal electrical check of component Y3/8y2 (K1 clutch control solenoid valve (VGS)) has failed.�
0778 The internal electrical check of component Y3/8y5 (B1 brake control solenoid valve (VGS)) has failed.�
0798 The internal electrical check of component Y3/8y7 (B3 brake control solenoid valve (VGS)) has failed.�
0893 Hydraulic fault in transmission (disengaging shift element does not disengage).�
0894 The gear is implausible or the transmission is slipping.�
1629 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
1631 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
1632 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
1633 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
1634 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
1636 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
1638 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
1639 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
1710 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
1711 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
1712 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
2216 Check component Y3/8s1 (Selection range sensor (VGS)). The adaptation sequence occurred outside the valid range.�
2711 Hydraulic fault in transmission (engaging shift element does not engage).�
2716 The internal electrical check of component Y3/8y4 (K3 clutch control solenoid valve (VGS)) has failed.�
2725 The internal electrical check of component Y3/8y6 (B2 brake control solenoid valve (VGS)) has failed.�
2734 The internal electrical check of component Y3/8y3 (K2 clutch control solenoid valve (VGS)) has failed.�
2759 The internal electrical check of component Y3/8y8 (Torque converter lockup clutch control solenoid valve (VGS)) has failed.�
2766 Excessive rpms have occurred at component Y3/8n2 (Internal speed sensor (VGS)).�
2767 The signal from component Y3/8n2 (Internal speed sensor (VGS)) is not available.�
2768 Component Y3/8n2 (Internal speed sensor (VGS)) is defective.�
2783 The friction power of the torque converter lockup clutch is too high.�
2805 The signals of the range selector sensor are implausible in comparison to the signals from the electronic selector lever module.�
2810 The internal electrical check of component Y3/8y1 (Working pressure control solenoid valve (VGS)) has failed.�
C001 CAN controller: CAN bus OFF�
C002 CAN controller: CAN bus OFF�
C300 Component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is defective.�
E0513 The CAN signal for start enable sent to the drive authorization system by transmission control is missing or invalid.�
E0562 The voltage supply of circuit 87 has undervoltage.�
E0563 The voltage supply of circuit 87 has overvoltage.�
E0602 Control module Y3/8n4 (Fully integrated transmission control (VGS) control unit) is not coded.�
E1644 The variant coding of component Y3/8n4 (Fully integrated transmission control (VGS) control unit) is implausible or no coding.�
E1707 Function shutoff of system due to excessive temperature and overvoltage�
E2638 Engine control does not allow any torque intervention by transmission control.�
E2806 Component Y3/8s1 (Selection range sensor (VGS)) is not learned.�
EC100 No CAN message was received from control unit Engine management.�
EC103 No CAN message was received from control unit N15/5 (Electronic selector lever module (ESM [EWM])).�
EC121 No CAN message was received from control unit N47-5 (ESP and BAS control module).�
EC126 One or more messages from control unit N80 (Steering column module) are not available on the CAN bus.�
EC141 No CAN message was received from control unit N73 (EIS [EZS] control unit).�
EC155 No CAN message was received from control unit A1 (Instrument cluster).�
EC164 No CAN message was received from control unit N22 (AAC [KLA] control and operating unit).�
EC167 No CAN message was received from control unit N73 (EIS [EZS] control unit) or N93 (Central gateway control unit).�
EC401 One or more signals sent from control unit Engine management via the CAN bus is implausible.�
EC404 No CAN message was received from control unit N15/5 (Electronic selector lever module (ESM [EWM])).�
EC415 One or more signals sent from control unit N47-5 (ESP and BAS control module) via the CAN bus is implausible.�
EC423 One or more signals sent from control unit A1 (Instrument cluster) via the CAN bus is implausible.�
EC424 One or more signals sent from control unit N22 (AAC [KLA] control and operating unit) via the CAN bus is implausible.�
EC428 No CAN message was received from control unit N80 (SCM [MRM] control unit).�
EC429 No CAN message was received from control unit N80 (Steering column module).�
EC431 One or more signals sent from control unit N73 (EIS [EZS] control unit) via the CAN bus is implausible.�
ED10B No CAN message was received from control unit Engine management.�
ED139 No CAN message was received from control unit N80 (SCM [MRM] control unit).�
ED13A No CAN message was received from control unit N80 (SCM [MRM] control unit).�
ED400 No CAN message was received from control unit Engine management.�
ED401 No CAN message was received from control unit Engine management.�
ED402 No CAN message was received from control unit Engine management.�
ED404 No CAN message was received from control unit Engine management.�
ED405 No CAN message was received from control unit Engine management.�
ED406 No CAN message was received from control unit Engine management.�
ED407 No CAN message was received from control unit N47-5 (ESP and BAS control module).�
ED408 No CAN message was received from control unit N47-5 (ESP and BAS control module).�
ED409 No CAN message was received from control unit N47-5 (ESP and BAS control module).�
ED40A No CAN message was received from control unit N47-5 (ESP and BAS control module).�
ED40B No CAN message was received from control unit N47-5 (ESP and BAS control module).�
ED40C No CAN message was received from control unit N47-5 (ESP and BAS control module).�
ED420 No CAN message was received from control unit N15/5 (Electronic selector lever module control unit).�
ED504 One or more signals sent from control unit N80 (Steering column module) via the CAN bus is implausible.�
ED507 One or more signals sent from control unit Engine management via the CAN bus is implausible.�
ED508 One or more signals sent from control unit N15/5 (Electronic selector lever module (ESM [EWM])) via the CAN bus is implausible.�
ED50B One or more of the signals transmitted by control unit N73 (EIS [EZS] control unit) or N93 (Central gateway control unit) via the CAN bus are implausible.