Part 3

- Property parameterization
- Function "speed limiter"
- Maximum speed

- Engine start/stop
- Signal settings
- Request "engine start" from discrete input
- Request "engine start" from body manufacturer CAN
- Condition for engine start: neutral position
- Condition for engine start: signal "hand brake" from discrete input
- Request "starter lockout" from discrete input
- Request "starter lockout" from body manufacturer CAN
- Request "engine stop" from discrete input
- Request "engine stop" from body manufacturer CAN

- Property parameterization
- Function "engine start"
- Function "engine stop"
- Condition for engine start: hand brake
- Condition for engine start: PTO engaged
- Condition for engine start: clutch

Global functions
These are structured as follows:
- Signal settings
- Internally wake PSM control unit

- Property parameterization
- Run-on time
- PSM control unit functionality "Internally wake PSM"
- Undervoltage detection: deactivation threshold
- Undervoltage detection: activation threshold
- Undervoltage detection: time until deactivation
- Undervoltage detection: time until activation
- Undervoltage detection: time until abort

Interfaces
The DAS menu item "Interfaces" provides an overview of all available interfaces and has the following structure:
- Submenu item "Discrete inputs"
- Submenu item "Discrete outputs"
- Submenu item "Signals to interior CAN bus"
- Submenu item "Signals to body CAN bus"

Discrete inputs
The "Discrete inputs" interface has the following submenu items in the DAS menu:
- Submenu item "Property parameterization"
- Submenu item "Switching thresholds for analog inputs 07 to 10"

The DAS menu item "Discrete inputs - Property parameterization" provides the possibility of, for example, setting the "Wake capability" parameter for the various discrete inputs.

Discrete outputs
The "Discrete outputs" interface has the following submenu items in the DAS menu:
- Submenu item "Signal settings"
- Submenu item "Property parameterization"
- Submenu item "Free PWM signals for outputs 09 and 10"

Signals to CAN-B
The "Signals to interior CAN bus" interface has the following submenu items in the DAS menu:
- Submenu item "Illumination and signaling horn"
- Submenu item "Alarm function"
- Submenu item "Sliding roof"
- Submenu item "Central locking"
- Submenu item "Wiping and heating of windows"
- Submenu item "Various functions"

Illumination and signaling horn
The "Switch on high beams" signal, for example, can be selected via the DAS mask "Illumination and signal selection".

Alarm function
The "Switch on front fog lamps" signal, for example, can be selected via the DAS mask "Alarm - Signal selection".

Sliding roof
The "Manually raise sliding roof" signal, for example, can be selected via the DAS mask "Sliding roof - Signal selection".

Central locking (CL [ZV])
The "Unlock front doors" signal, for example, can be selected via the DAS mask "Central locking - Signal selection".

Wiping and heating of windows
The "Actuate touch wiping" signal, for example, can be selected via the DAS mask "Wiping and heating of windows - Signal selection".

Various functions
The "Activate starter lockout" signal, for example, can be selected via the DAS mask "Various functions - Signal selection".

Signals for body manufacturer CAN
The "Signals to body CAN bus" interface has the following submenu items in the DAS menu:
- Submenu item "Signal settings"
- Submenu item "Property parameterization"

Logic functions (PLC)
All PLC functionalities can be realized using the DAS menu item "Logic functions (PLC)". The menu item has the following structure:
- Submenu item "Activate/deactivate PLC groups"
- Submenu item "PLC group 1"

Activate or deactivate PLC groups
All 4 PLC groups can be activated using the DAS menu item "Activation of PLC groups - Property parameterization".

All of the submenu items are shown below using PLC group 1 as an example. PLC groups 2 to 4 are activated and parameterized in the same way as PLC group 1.

PLC group 1
If, for example, PLC group 1 is selected, the following submenu items of PLC group 1 can be coded via the DAS menu item "PLC group 1- Selection of function group":
- Submenu item "Logic blocks"
- Submenu item "Flip-flops"
- Submenu item "Timer"
- Submenu item "Counter"
- Submenu item "Threshold switch"
- Submenu item "Hysteresis block"

Logic blocks
The signals and parameters of the selected logic blocks can be set in the two following submenu items under the DAS menu item "PLC group 1, logic blocks:
- Submenu item "Signal settings"
- Submenu item "Property parameterization"

PLC group 1, logic blocks - Signal selection
In the DAS menu item "PLC group 1, logic blocks - Signal selection", a signal is assigned to each input of the selected logic block.

PLC group 1, logic blocks - Property parameterization
The DAS menu item "PLC group 1, logic blocks - Property parameterization" provides the possibility of configuring the selected logic block. The logic block consists of 3 logical combinations (X, Y, Z) the characteristics of which can be parameterized individually.

Flip-Flops
Parameterization takes place as with logic blocks via the menus "Signal adjustments" and "Property parameterization".

Timer
Parameterization takes place as with logic blocks via the menus "Signal adjustments" and "Property parameterization".

Counter
Parameterization takes place as with logic blocks via the menus "Signal adjustments" and "Property parameterization".

Threshold switch
Parameterization takes place as with logic blocks via the menus "Signal adjustments" and "Property parameterization".

Hysteresis block
Parameterization takes place as with logic blocks via the menus "Signal adjustments" and "Property parameterization".

PLC group 2
All menu items are the same as for PLC group 1.

PLC group 3
All menu items are the same as for PLC group 1.

PLC group 4
All menu items are the same as for PLC group 1.

Special functions
Engine functions are implemented via the DAS menu mask "Special functions". The menu has the following structure:
- Submenu item "Engine speed control"
- Submenu item "Power take-off"
- Submenu item "Speed limiter"
- Submenu item "Engine start/stop"

Engine speed control

Working speed control
The following submenu items can be selected via the DAS mask "Engine speed control - Selection of function group":
- Submenu item "Working speed control"
- Submenu item "Change of engine speed"
- Submenu item "Rpm limitation"
- Submenu item "Fixed speed"
- Submenu item "Hand throttle actuator"

If the function group "Working speed control" is selected, this DAS menu mask can be used to set signals under the two following submenu items:
- Submenu item "Signal settings"
- Submenu item "Property parameterization"

In the example "Working speed control", the signals are set in the DAS menu mask "Working speed control - Signal selection".

The signal parameters for the example "Working speed control" are set in the DAS menu mask "Working speed control - Property parameterization".

Change of engine speed
Parameterization takes place as with working speed control via the menus "Signal adjustments" and "property parameterizing".

Rpm limitation
Parameterization takes place as with working speed control via the menus "Signal adjustments" and "property parameterizing".

Fixed speed
Parameterization takes place as with working speed control via the menus "Signal adjustments" and "property parameterizing".

Hand throttle actuator
Parameterization takes place as with working speed control via the menus "Signal adjustments" and "property parameterizing".

Power take-off
Parameterization takes place as with working speed control via the menus "Signal adjustments" and "property parameterizing".

Speed limiter
Parameterization takes place as with working speed control via the menus "Signal adjustments" and "property parameterizing".

Engine start/stop
Parameterization takes place as with working speed control via the menus "Signal adjustments" and "property parameterizing".

Global functions
The DAS menu mask "Global functions" provides the possibility of setting global parameters. The menu is divided into the following two submenu items:
- Submenu item "Signal settings"
- Submenu item "Property parameterization"

In the example "Global functions", the signals are set via the DAS menu mask "Global functions - Signal selection".
The parameters of "global functions" are adjusted via the DAS menu mask "Global functions - property parameterization".