Pinpoint Tests AM: The Safety Belt Warning Chime Does Not Operate Correctly/The Belt-Minder(R) Feature Does Not Operate Correct
Instrumentation, Message Center and Warning Chimes
Pinpoint Test AM: The Safety Belt Warning Chime Does Not Operate Correctly/The Belt-Minder(R) Feature Does Not Operate Correctly
Normal Operation
The Instrument Panel Cluster (IPC) receives the safety belt and Belt-Minder(R) requests from the Restraints Control Module (RCM) over the High Speed Controller Area Network (HS-CAN). The safety belt warning chime sounds for approximately 6 seconds when the driver or passenger safety belt is not fastened and the ignition is switched from the OFF or ACC to the RUN mode.
The Belt-Minder(R) feature supplements the safety belt warning function and is enabled after the safety belt warning is complete. The Belt-Minder(R) simultaneously sounds the chime and illuminates the safety belt warning lamp in the IPC once the vehicle speed has exceeded 9.7 km/h (6 mph), and remains active for 5 minutes from the time it is started.
There are 2 Belt-Minder(R) strategies that are used and implemented by the IPC as commanded by the RCM. The 2 strategies are designed to provide an increased chime tone activity. Belt-Minder(R) A provides 6 one-second sequences for the first minute of the Belt-Minder(R) warning. Belt-Minder(R) B provides 6 one-second sequences of 3 chime tones in rapid succession for the remainder of the Belt-Minder(R) warning.
The Belt-Minder(R) functions exactly the same for both MyKey(TM) and administrator keys except that when a MyKey(TM) is in use, the driver cannot configure the Belt-Minder(R) off. Once the Belt-Minder(R) is activated, the Belt-Minder(R) continues to chime periodically (without the 5 minute time out) and the audio unit is muted until the driver and passenger safety belts are fastened.
NOTE: Make sure that the Belt-Minder(R) chime operation is verified with the vehicle moving at least 9.7 km/h (6 mph).
This pinpoint test is intended to diagnose the following:
- Safety belt warning indication concern
- Belt-Minder(R) deactivated
- Speedometer concern
- RCM
- IPC
PINPOINT TEST AM: THE SAFETY BELT WARNING CHIME IS INOPERATIVE/THE BELT-MINDER(R) FEATURE DOES NOT OPERATE CORRECTLY
-------------------------------------------------
AM1 CHECK THE KEY-IN-IGNITION WARNING CHIME OPERATION
- Ignition OFF.
- On vehicles without Intelligent Access (IA), insert the key into the ignition lock cylinder.
- On vehicles equipped with IA, place the ignition in the ACC mode.
- Open the LH front door and observe the key-in-ignition warning chime operation.
- Does the key-in-ignition warning chime operate correctly?
Yes
GO to AM2.
No
INSTALL a new IPC. REFER to Instrument Panel Cluster (IPC) Instrument Panel Cluster (IPC). TEST the system for normal operation.
-------------------------------------------------
AM2 CHECK THE DRIVER AND FRONT PASSENGER SAFETY BELT BUCKLE SWITCHES
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: RCM PIDs.
- Monitor the RCM driver safety belt buckle PID (SBLT_D_ST) and the front passenger safety belt buckle PID (SBLT_P_ST) while buckling and unbuckling the driver and RH front passenger safety belts.
- Do the PIDs display BUCKLED with the safety belt buckled and UNBUCKLED with the safety belt unbuckled?
Yes
GO to AM3.
No
REFER to Restraint Systems.
-------------------------------------------------
AM3 CHECK THE SAFETY BELT WARNING INDICATOR FOR CORRECT OPERATION
- Ignition ON.
- Within one minute, buckle then unbuckle the LH front safety belt.
- With the engine running, verify the safety belt warning indicator illuminates with the safety belt unbuckled and turns off when buckled.
- Does the safety belt warning indicator operate correctly?
Yes
GO to AM4.
No
GO to Pinpoint Test Q. Pinpoint Test Q: The Safety Belt Warning Indicator Is Never/Always On
-------------------------------------------------
AM4 CHECK THE SPEEDOMETER OPERATION
- Verify that the speedometer is operating correctly.
- Does the speedometer operate correctly?
Yes
GO to AM5.
No
GO to Pinpoint Test F. Pinpoint Test F: The Speedometer Is Inoperative
-------------------------------------------------
AM5 CHECK THE BELT-MINDER(R) CONFIGURATION
NOTE: Verify that an administrator key is used for this test and not a MyKey(TM) programmed key. When a MyKey(TM) programmed key is used, the Belt-Minder(R) is automatically turned on and cannot be disabled (if previously disabled by an administrator, the Belt-Minder(R) remains disabled when an administrator key is used).
- Verify that the Belt-Minder(R) is activated or configured on for the seating position in question. Refer to Belt-Minder(R) Deactivating/Activating Service and Repair to configure without a scan tool.
- Is the Belt-Minder(R) activated for the seating position in question?
Yes
INSTALL a new RCM. REFER to Restraint Systems. TEST the system for normal operation.
No
ACTIVATE the Belt-Minder(R) for the seating position in question. REFER to Belt-Minder(R) Deactivating/Activating Service and Repair. TEST the system for normal operation.
-------------------------------------------------