P1235

1UR-FSE ENGINE CONTROL SYSTEM: SFI SYSTEM: P1235, P1236: High Pressure Fuel Pump Circuit
P1236 - High Pressure Fuel Pump No. 2 Circuit

DESCRIPTION

The fuel pump for high pressure is attached to the insulator, which is attached to the cylinder head cover. The pump activates according to the position of the cam on the intake side camshaft (bank 1 and bank 2).

The fuel pump for high pressure increases the pressure of the fuel supplied from the fuel pump in the fuel tank to 4 to 13 MPa (40.8 to 132.6 kgf/cm2, 580 to 1885 psi) according to the operating condition, and it feeds the fuel to the fuel delivery pipe.





MONITOR STRATEGY





TYPICAL ENABLING CONDITIONS





TYPICAL MALFUNCTION THRESHOLDS





CONFIRMATION DRIVING PATTERN





1. Connect the Techstream to the DLC3.

2. Turn the engine switch on (IG) and turn the Techstream on.

3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) Reading and Clearing Diagnostic Trouble Codes.

4. Turn the engine switch off and wait for at least 30 seconds.

5. Turn the engine switch on (IG) and turn the Techstream on [A].

6. Start the engine.

7. Idle the engine for 10 seconds [B].

8. Enter the following menus: Powertrain / Engine / Trouble Codes.

9. Read the DTCs [C].

HINT
- If a DTC is output, the system is malfunctioning.
- If a DTC is not output, perform the following procedure.

10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11. Input the DTC: P1235 and P1236.

12. Check the DTC judgment result.





HINT
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

13. If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs Reading and Clearing Diagnostic Trouble Codes.

HINT
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTC is output, the system is normal.

WIRING DIAGRAM





INSPECTION PROCEDURE

HINT
- Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
- Bank 2 refers to the bank that does not include the No. 1 cylinder.

PROCEDURE

1. CHECK DTC

(a) Interchange the injector driver No. 1 and No. 2 Removal.





(b) Connect the Techstream to the DLC3.

(c) Turn the engine switch on (IG) and turn the Techstream on.

(d) Clear DTCs Reading and Clearing Diagnostic Trouble Codes.

NOTICE:
Before deleting the DTCs, write them down.

(e) Start the engine.

(f) Enter the following menus: Powertrain / Engine / Trouble Codes.

(g) Read DTC.

Result:





B -- REPLACE INJECTOR DRIVER Removal
A -- Continue to next step.

2. INSPECT SPILL CONTROL VALVE

(a) Disconnect the E43 or E35 spill control valve connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- REPLACE FUEL PUMP FOR HIGH PRESSURE Removal
OK -- Continue to next step.

3. CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - SPILL CONTROL VALVE)

(a) Disconnect the E16 or E28 injector driver (EDU) connector.





(b) Disconnect the E43 or E35 spill control valve connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):

No. 1





No. 2





Standard resistance (Check for short):

No. 1





No. 2





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

4. CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)

(a) Disconnect the E15 injector driver (No. 1) connector.





(b) Disconnect the E27 injector driver (No. 2) connector.

(c) Disconnect the E4 ECM connector.

(d) Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):





Standard resistance (Check for short):





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR

OK -- REPLACE ECM Removal