Reassembly

PARKING BRAKE: PARKING BRAKE ASSEMBLY: REASSEMBLY

1. APPLY HIGH TEMPERATURE GREASE

(a) Apply high temperature grease to the areas of the backing plate which make contact with the shoe as shown in the illustration.





2. INSTALL PARKING BRAKE SHOE HOLD DOWN SPRING PIN

(a) Install the 2 parking brake shoe hold down spring pins.

3. INSTALL NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING

(a) Install the No. 1 parking brake shoe return tension spring to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly.

4. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET

(a) Apply high temperature grease to the parking brake shoe adjusting screw set as shown in the illustration.





(b) Install the parking brake shoe adjusting screw set to the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly.

5. INSTALL PARKING BRAKE SHOE LEVER

(a) Using needle-nose pliers, install the parking brake shoe lever to the No. 3 parking brake cable assembly.

(b) Apply high temperature grease to the areas of the parking brake shoe lever which make contact with the No. 2 parking brake shoe assembly.

(c) Install the parking brake shoe lever to the No. 2 parking brake shoe assembly.

(d) Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and fit them to the backing plate.





NOTICE:
Make sure that the parking brake shoe lever does not separate from the No. 2 parking brake shoe assembly.

6. INSTALL PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Rear Side)

(a) Using SST, install the parking brake shoe hold down compression spring as shown in the illustration.





SST : 09718-00011

7. INSTALL PARKING BRAKE SHOE STRUT

(a) Install the parking brake shoe strut.

(b) Install the No. 1 parking brake shoe assembly.





8. INSTALL PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Front Side)

(a) Using SST, install the parking brake shoe hold down compression spring as shown in the illustration.





SST : 09718-00011

9. INSTALL NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING

(a) Install the No. 2 parking brake shoe return tension spring.

10. INSTALL NO. 3 PARKING BRAKE SHOE RETURN TENSION SPRING

(a) Install the No. 3 parking brake shoe return tension spring.

11. CHECK PARKING BRAKE INSTALLATION

(a) Check that each part is installed properly.





Text in Illustration





NOTICE:
There should be no oil or grease on the friction surfaces of the shoe lining and disc.

12. INSTALL REAR DISC Installation

13. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY Installation

14. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL Adjustments

15. INSTALL REAR WHEEL

Torque : 103 Nm (1050 kgf-cm, 76 ft-lbf)

16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

(a) Connect the cable to the negative (-) battery terminal and close the front luggage compartment trim cover.

(b) Connect the reservoir level switch connector.

(c) Clear the DTCs Reading and Clearing Diagnostic Trouble Codes.

17. INSTALL LUGGAGE COMPARTMENT FLOOR MAT Installation

18. BED IN PARKING BRAKE SHOES TO DISCS

(a) Drive the vehicle at about 50 km/h (31 mph) on a safe, level and dry road.

(b) Depress the parking brake pedal with 150 N (15 kgf, 33.7 lbf) of force.

(c) Drive the vehicle for about 400 m (0.25 mile) in this condition.

(d) Repeat this procedure 3 times.

NOTICE:
Set a 5-minute interval between each procedure to prevent the brake assembly from overheating.