FREE REPAIR MANUALS & LABOR GUIDES 1982-2013 Vehicles
Courtesy of Operation CHARM: Car repair manuals for everyone.
Home >> Lexus >> 2010 >> IS 250 RWD V6-2.5L (4GR-FSE) >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> P Code Charts >> P0453

P0453





4GR-FSE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0451-P0453: Evaporative Emission Control System Pressure Sensor Range / Performance


DTC SUMMARY





HINT
The pressure sensor is built into the pump module.

DESCRIPTION

The circuit description can be found in the EVAP (Evaporative Emission) System EVAP System.

MONITOR DESCRIPTION





- DTC P0451: Pressure sensor noising or stuck

- If the pressure sensor output voltage fluctuates rapidly for 10 seconds, the ECM stops the EVAP system monitor. The ECM interprets this as noise from the pressure sensor, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC.

- Alternatively, if the sensor output voltage does not change for 10 seconds, the ECM interprets this as the sensor being stuck, and stops the monitor. The ECM then illuminates the MIL and sets the DTC.

- (Both the malfunctions are detected by 2 trip detection logic).

- DTC P0452: Pressure sensor voltage low

- If the pressure sensor output voltage is below 0.45 V, the ECM interprets this as an open or short circuit malfunction in the pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC (1 trip detection logic).

- DTC P0453: Pressure sensor voltage high

- If the pressure sensor voltage output is 4.9 V or more, the ECM interprets this as an open or short circuit malfunction in the pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC (1 trip detection logic).

MONITOR STRATEGY





TYPICAL ENABLING CONDITIONS

P0451: Canister pressure sensor noise

P0451: Canister pressure sensor noise:





P0451: Canister pressure sensor stuck

P0451: Canister pressure sensor stuck:





P0452 and P0453:

P0452 and P0453::





TYPICAL MALFUNCTION THRESHOLDS

P0451: Canister pressure sensor noise

P0451: Canister pressure sensor noise:





P0451: Canister pressure sensor stuck

P0451: Canister pressure sensor stuck:





P0452: Canister pressure sensor low voltage

P0452: Canister pressure sensor low voltage:





P0453: Canister pressure sensor high voltage

P0453: Canister pressure sensor high voltage:





CONFIRMATION DRIVING PATTERN





NOTICE:
- The Evaporative System Check (Automatic Mode) consists of 5 steps performed automatically by the Techstream. It takes a maximum of approximately 18 minutes.
- Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
- Do not run the engine during this operation.
- When the temperature of the fuel is 35°C (95°F) or more, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F).
- Connect the Techstream to the DLC3.

- Turn the engine switch on (IG) and turn the Techstream on.

- Enter the following menus: Powertrain / Engine / Data List / Intake Air.

- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) DTC Check / Clear.

- Turn the engine switch off and wait for 30 seconds.

- Turn the engine switch on (IG) and turn the Techstream on.

- Enter the following menus: Powertrain / Engine / Utility / Evaporative System Check / Automatic Mode [A].

- Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

- Read the pending DTC [B].

HINT
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.

- Input the DTC: P0451, P0452 or P0453.

- Check the DTC judgment result.





HINT
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows INCOMPLETE or UNKNOWN, perform step [A] again.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.

- Check the DTC judgment result.

HINT
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows NORMAL, the system is normal.
- If the test result is INCOMPLETE or UNKNOWN and no pending DTC is output, perform a universal trip and check for permanent DTCs DTC Check / Clear.

HINT
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTC is output, the system is normal.
WIRING DIAGRAM





INSPECTION PROCEDURE

NOTICE:
- When a vehicle is brought into a workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel tank cap.
- Do not disassemble the pump module.
- Techstream is required to conduct the following diagnostic troubleshooting procedure.
PROCEDURE

1. CONFIRM DTC AND EVAP PRESSURE

(a) Connect Techstream to the DLC3.

(b) Turn the engine switch on (do not start the engine).

(c) Turn the tester on.

(d) Enter the following menus: Powertrain / Engine / Trouble Codes.

(e) Read DTCs.

(f) Enter the following menus: Powertrain / Engine / Data List / EVAP / Vapor Pressure Pump.

(g) Read the EVAP (Evaporative Emission) pressure displayed on the tester.

Result:





C -- GO TO EVAP INSPECTION PROCEDURE

B -- CHECK HARNESS AND CONNECTOR (PUMP MODULE - ECM)
A -- Continue to next step.

2. CHECK HARNESS AND CONNECTOR (PUMP MODULE - ECM)

(a) Turn the engine switch off.

(b) Disconnect the A6 ECM connector.

(c) Measure the resistance between the PPMP terminal of the ECM connector and body ground.

Result:





(d) Reconnect the ECM connector.

B -- REPLACE ECM
A -- Continue to next step.

3. CHECK HARNESS AND CONNECTOR (PUMP MODULE - ECM)

(a) Disconnect the Q49 canister pump module pump module connector.

(b) Disconnect the A6 ECM connector.

(c) Measure the resistance between the PPMP terminal of the ECM connector and body ground.

Result:





(d) Reconnect the canister pump module connector.

(e) Reconnect the ECM connector.

B -- REPAIR OR REPLACE HARNESS OR CONNECTOR

A -- REPLACE CHARCOAL CANISTER

4. CHECK HARNESS AND CONNECTOR (PUMP MODULE - ECM)

(a) Disconnect the Q49 canister pump module connector.

(b) Turn the engine switch on (IG).

(c) Measure the voltage and resistance according to the value(s) in the table below.

Standard voltage:





Standard resistance:





Result:





(d) Reconnect the canister pump module connector.

B -- REPAIR OR REPLACE HARNESS OR CONNECTOR

A -- REPLACE CHARCOAL CANISTER

5. REPLACE CHARCOAL CANISTER

NEXT -- CHECK WHETHER DTC OUTPUT (AFTER REPAIR)

6. REPAIR OR REPLACE HARNESS OR CONNECTOR

HINT
If the exhaust tail pipe has been removed, go to the next step before reinstalling it.

NEXT -- CHECK WHETHER DTC OUTPUT (AFTER REPAIR)

7. REPLACE ECM

(a) Replace the ECM Removal.

NEXT -- CHECK WHETHER DTC OUTPUT (AFTER REPAIR)

8. CHECK WHETHER DTC OUTPUT (AFTER REPAIR)

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(c) Turn the Techstream on.

(d) Clear the DTCs DTC Check / Clear.

(e) Turn the engine switch off and wait for 30 seconds.

(f) Turn the engine switch on (IG) and turn the Techstream on.

(g) Start the engine and warm it up.

(h) Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

(i) Enter the following menus: Powertrain / Engine / Utility / All Readiness.

(j) Input the DTC: P0451, P0452 or P0453.

(k) Check the DTC judgment result.

HINT
If DTC judgment result is NORMAL, the repair has been successfully completed.

NEXT -- END
pro multis Credits:Operation CHARM About Operation CHARM