Rear Speed Sensor RH Circuit - Electronically Controlled Brake System

BRAKE CONTROL: ELECTRONICALLY CONTROLLED BRAKE SYSTEM: C0210/33,C0215/34,C1273/73,C1274/74: Rear Speed Sensor RH Circuit
C1274/74 - Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DESCRIPTION

Refer to DTC C0200/31 and C0205/32 C0200.

DTCs C1273/73 and C1274/74 can be deleted when the speed sensor sends a vehicle speed signal or the Test Mode ends. DTCs C1273/73 and C1274/74 are output only in the Test Mode.

HINT
* DTC C0210/33 is for the right rear speed sensor.
* DTC C0215/34 is for the left rear speed sensor.
WIRING DIAGRAM

INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU, perform initialization of linear solenoid valve and calibration Initialization.

PROCEDURE

1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)

(a) Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to a DTC Check For Intermittent Problems.

ABS / VSC / TRAC:

OK:

There are no momentary interruptions.

HINT
Perform the above inspection before removing the sensor and connector.

NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)
OK -- Continue to next step.

2. READ VALUE USING TECHSTREAM (REAR SPEED SENSOR)

(a) Connect the Techstream to the DLC3.

(b) Start the engine.

(c) Select the Data List mode on the Techstream.

ABS / VSC / TRAC:

(d) Check that the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer are almost the same when driving the vehicle.

OK:

The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed.

ABS / VSC / TRAC:

(e) Check that the sensor signal conforms to the wheel direction.

OK:

The wheel direction is displayed.

NG -- INSPECT REAR SPEED SENSOR INSTALLATION
OK -- Continue to next step.

3. PERFORM TEST MODE (SIGNAL CHECK)

(a) Clear the DTC Electronically Controlled Brake System.

(b) Perform sensor signal check in TEST MODE PROCEDURE Electronically Controlled Brake System.

OK:

All Test Mode DTCs are erased.

NG -- INSPECT REAR SPEED SENSOR INSTALLATION
OK -- Continue to next step.

4. RECONFIRM DTC

(a) Clear the DTC Electronically Controlled Brake System.

(b) Start the engine.

(c) Drive the vehicle at the speed of 32 km/h (20 mph) or more for 60 seconds or more.

(d) Check if the same DTCs are recorded Electronically Controlled Brake System.

Result:

OK:

There is no clearance between the sensor and the rear axle carrier.

The installation bolt is tightened properly.

Torque: 8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
Check the speed sensor signal after replacement Electronically Controlled Brake System.

NG -- CHECK AND REPLACE REAR SPEED SENSOR
OK -- Continue to next step.

6. INSPECT REAR SPEED SENSOR TIP

(a) Remove the rear speed sensor.

(b) Check the sensor tip.

OK:

No scratches or foreign matter on the sensor tip.

NOTICE:
Check the speed sensor signal after cleaning/replacement Electronically Controlled Brake System.

NG -- CLEAN OR REPLACE REAR SPEED SENSOR
OK -- Continue to next step.

7. CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)

(a) Disconnect the skid control sensor wire.

(b) Measure the resistance according to the value(s) in the table below.

Resistance:

RH
LH

NOTICE:
Check the speed sensor signal after replacement Electronically Controlled Brake System.

NG -- REPLACE SKID CONTROL SENSOR WIRE
OK -- Continue to next step.

8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU TO REAR SPEED SENSOR)

(a) Disconnect the skid control ECU (A13, A15) connectors and the rear speed sensor connector.

(b) Measure the resistance according to the value(s) in the table below.

Resistance:

RH
LH

NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

9. INSPECT SKID CONTROL ECU (SENSOR INPUT VOLTAGE)

(a) Reconnect the skid control ECU (A13, A15) connectors.

(b) Disconnect the speed sensor connector.

(c) Turn the engine switch on (IG).

(d) Measure the voltage according to the value(s) in the table below.

Voltage:

NG -- REPLACE SKID CONTROL ECU
OK -- Continue to next step.

10. RECONFIRM DTC

(a) Clear the DTC Electronically Controlled Brake System.

(b) Start the engine.

(c) Drive the vehicle at the speed of 32 km/h (20 mph) or more for 60 seconds or more.

(d) Check if the same DTCs are recorded Electronically Controlled Brake System.

HINT
Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.

Result:

HINT
If troubleshooting has been carried out according to the PROBLEM SYMPTOMS TABLE, refer back to the table and proceed to the next step Problem Symptoms Table.

B -- REPLACE REAR SPEED SENSOR

A -- END

11. REPLACE REAR SPEED SENSOR

(a) Replace the rear speed sensor Removal.

NOTICE:
Check the speed sensor signal after replacement Electronically Controlled Brake System.

NEXT -- Continue to next step.

12. RECONFIRM DTC

(a) Clear the DTC Electronically Controlled Brake System.

(b) Start the engine.

(c) Drive the vehicle at the speed of 32 km/h (20 mph) or more for 60 seconds or more.

(d) Check if the same DTCs are recorded Electronically Controlled Brake System.

HINT
Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.

Result:

HINT
If troubleshooting has been carried out according to the PROBLEM SYMPTOMS TABLE, refer back to the table and proceed to the next step Problem Symptoms Table.

B -- END
A -- Continue to next step.

13. INSPECT SPEED SENSOR ROTOR

(a) Remove the speed sensor rotor.

(b) Check the sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.

NOTICE:
Check the speed sensor signal after cleaning/replacement Electronically Controlled Brake System.

NG -- CLEAN OR REPLACE SPEED SENSOR ROTOR

OK -- REPLACE SKID CONTROL ECU