Shift Solenoid: Testing and Inspection

A761E AUTOMATIC TRANSMISSION: SHIFT SOLENOID VALVE: INSPECTION

INSPECTION

1. INSPECT SHIFT SOLENOID VALVE SL1





(a) Measure the resistance of the valve.
Standard resistance:






(b) Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.
OK:
Valve moves and makes operating noise.
NOTE:
While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

2. INSPECT SHIFT SOLENOID VALVE S1





(a) Measure the resistance according to the value(s) in the table below.
Standard resistance:






(b) Connect the battery's positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.
OK:
Valve moves and makes operating noise.
NOTE:
While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

3. INSPECT SHIFT SOLENOID VALVE S2





(a) Measure the resistance of the valve.
Standard resistance:






(b) Connect the battery's positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.
OK:
Valve moves and makes operating noise.
NOTE:
While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

4. INSPECT SHIFT SOLENOID VALVE S3





(a) Measure the resistance of the valve.
Standard resistance:






(b) Connect the battery's positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.
OK:
Valve moves and makes operating noise.
NOTE:
While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

5. INSPECT SHIFT SOLENOID VALVE S4





(a) Measure the resistance of the valve.
Standard resistance:






(b) Connect the battery's positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.
OK:
Valve moves and makes operating noise.
NOTE:
While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

6. INSPECT SHIFT SOLENOID VALVE SL2





(a) Measure the resistance of the valve.
Standard resistance:






(b) Connect the battery's positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.
OK:
Valve moves and makes operating noise.
NOTE:
While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

7. INSPECT SHIFT SOLENOID VALVE SR





(a) Measure the resistance of the valve.
Standard resistance:






(b) Connect the battery's positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.
OK:
Valve moves and makes operating noise.
NOTE:
While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

8. INSPECT SHIFT SOLENOID VALVE SLT





(a) Measure the resistance of the valve.
Standard resistance:






(b) Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 of the solenoid valve connector and the negative (-) lead to terminal 1, and check the operation of the valve.
OK:
Valve moves and makes operating noise.
NOTE:
While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

9. INSPECT SHIFT SOLENOID VALVE SLU





(a) Measure the resistance of the valve.
Standard resistance:






(b) Connect the battery's positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.
OK:
Valve moves and makes operating noise.
NOTE:
While using the battery during the inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.