System Specifications

Cylinder block warpage
Maximum 0.07 mm (0.0028 in.)
Cylinder bush bore diameter
Use standard 10.285 to 10.306 mm (0.4049 to 0.4057 in.)
Use O/S 0.05 10.335 to 10.356 mm (0.4069 to 0.4077 in.)

Crankshaft bearing cap set bolt diameter
Standard 10.8 to 11.0 mm (0.4252 to 0.4331 in.)
Minimum 10.7 mm (0.4213 in.)
Crankshaft bearing cap x Cylinder block
1st for 16 point head 61 Nm (622 kgf-cm, 45 ft lbf)
2nd for 16 point head Turn 90�
for 12 mm head 26 Nm (265 kgf-cm, 19 ft lbf)

Crankshaft circle runout
Maximum 0.06 mm (0.0024 in.)
Main journal diameter 60.988 to 61.000 mm (2.4011 to 2.4016 in.)

Main journal taper and out-of -round
Maximum 0.02 mm (0.0008 in.)
Crank pin diameter 52.992 to 53.000 mm (2.0863 to 2.0866 in.)

Crank pin taper and out-of-round
Maximum 0.02 mm (0.0008 in.)

Crankshaft oil clearance
Standard 0.045 to 0.067 mm (0.0018 to 0.0026 in.)
Minimum 0.070 mm (0.0028 in.)

Standard crankshaft main journal diameter
Mark 00 60.999 to 61.000 mm (2.4015 to 2.4016 in.)
Mark 01 60.998 to 60.999 mm (2.4015 to 2.4015 in.)
Mark 02 60.997 to 60.998 mm (2.4015 to 2.4015 in.)
Mark 03 60.996 to 60.997 mm (2.4014 to 2.4015 in.)
Mark 04 60.995 to 60.996 mm (2.4014 to 2.4014 in.)
Mark 05 60.994 to 60.995 mm (2.4013 to 2.4014 in.)
Mark 06 60.993 to 60.994 mm (2.4013 to 2.4013 in.)
Mark 07 60.992 to 60.993 mm (2.4013 to 2.4013 in.)
Mark 08 60.991 to 60.992 mm (2.4012 to 2.4013 in.)
Mark 09 60.990 to 60.991 mm (2.4012 to 2.4012 in.)
Mark 10 60.989 to 60.990 mm (2.4011 to 2.4012 in.)
Mark 11 60.988 to 60.989 mm (2.4011 to 2.4011 in.)
Standard upper bearing center wall thickness
No. 1 and No. 4 journal
Mark 1 2.500 to 2.503 mm (0.0984 to 0.0985 in.)
Mark 2 2.503 to 2.506 mm (0.0985 to 0.0987 in.)
Mark 3 2.506 to 2.509 mm (0.0987 to 0.0988 in.)
Mark 4 2.509 to 2.512 mm (0.0988 to 0.0989 in.)
Mark 5 2.512 to 2.515 mm (0.0989 to 0.0990 in.)
Standard upper bearing center wall thickness
No. 2 and No. 3 journal
Mark 1 2.478 to 2.481 mm (0.0976 to 0.0977 in.)
Mark 2 2.481 to 2.484 mm (0.0977 to 0.0978 in.)
Mark 3 2.484 to 2.487 mm (0.0978 to 0.0979 in.)
Mark 4 2.487 to 2.490 mm (0.0979 to 0.0980 in.)
Mark 5 2.490 to 2.493 mm (0.0980 to 0.0981 in.)
Standard lower bearing center wall thickness
No. 1 and No. 4 journal
Mark 1 2.475 to 2.478 mm (0.0974 to 0.0976 in.)
Mark 2 2.478 to 2.481 mm (0.0976 to 0.0977 in.)
Mark 3 2.481 to 2.484 mm (0.0977 to 0.0978 in.)
Mark 4 2.484 to 2.487 mm (0.0978 to 0.0979 in.)
Mark 5 2.487 to 2.490 mm (0.0979 to 0.0980 in.)
Standard lower bearing center wall thickness
No. 2 and No. 3 journal
Mark 1 2.497 to 2.500 mm (0.0983 to 0.0984 in.)
Mark 2 2.500 to 2.503 mm (0.0984 to 0.0985 in.)
Mark 3 2.503 to 2.506 mm (0.0985 to 0.0987 in.)
Mark 4 2.506 to 2.509 mm (0.0987 to 0.0988 in.)
Mark 5 2.509 to 2.512 mm (0.0988 to 0.0989 in.)

Crankshaft thrust clearance
Standard 0.04 to 0.24 (0.0016 to 0.0094 in.)
Maximum 0.30 mm (0.0118 in.)
Thrust washer thickness 2.43 to 2.48 mm (0.0957 to 0.0976 in.)

Connecting rod big end inside diameter
Mark 1 56.000 to 56.006 mm (2.2047 to 2.2050 in.)
Mark 2 56.007 to 56.012 mm (2.2050 to 2.2052 in.)
Mark 3 56.013 to 56.018 mm (2.2052 to 2.2054 in.)
Mark 4 56.019 to 56.024 mm (2.2055 to 2.2057 in.)
Standard sized bearing center wall thickness
Mark 1 1.481 to 1.484 mm (0.0583 to 0.0584 in.)
Mark 2 1.484 to 1.487 mm (0.0584 to 0.0585 in.)
Mark 3 1.487 to 1.490 mm (0.0585 to 0.0587 in.)
Mark 4 1.490 to 1.493 mm (0.0587 to 0.0588 in.)

Connecting rod thrust clearance
Standard 0.15 to 0.40 (0.0059 to 0.0157 in.)
Maximum 0.50 mm (0.0197 in.)
Connecting rod oil clearance
Standard 0.045 to 0.067 (0.0018 to 0.0026 in.)
Maximum 0.070 mm (0.0028 in.)
Connecting rod out-of alignment
Maximum 0.05 mm (0.0020 in.) per 100 mm (3.94 in.)
Connecting rod twist
Maximum 0.15 mm (0.0059 in.) per 100 mm (3.94 in.)
Connecting rod bushing inside diameter
Mark A 22.005 to 22.008 mm (0.8663 to 0.8665 in.)
Mark B 22.009 to 22.012 mm (0.8665 to 0.8666 in.)
Mark C 22.011 to 22.014 mm (0.8666 to 0.8667 in.)
Connecting rod bushing oil clearance
Standard 0.005 to 0.011 mm (0.0002 to 0.0004 in.)
Maximum 0.03 mm (0.0012 in.)
Connecting rod bolt diameter
Standard 8.5 to 8.6 mm (0.335 to 0.339 in.)
Minimum 8.3 mm (0.327 in.)
Connecting rod cap x Connecting rod sub-assembly
1st 40 Nm (408 kgf-cm, 30 ft lbf)
2nd Turn 90�

Piston diameter
Distance 9.1 mm (0.36 in.)
Standard 93.960 to 93.980 mm (3.6992 to 3.6999 in.)
Maximum 93.830 mm (3.6941 in.)
Piston oil clearance
Standard 0.020 to 0.052 mm (0.0008 to 0.0020 in.)
Maximum 0.370 mm (0.0146 in.)
Piston ring groove clearance
No. 1 0.020 to 0.070 mm (0.0008 to 0.0028 in.)
No. 2 0.020 to 0.060 mm (0.0008 to 0.0024 in.)
Oil 0.020 to 0.070 mm (0.0008 to 0.0028 in.)
Piston ring end gap
Standard
No. 1 0.23 to 0.33 mm (0.0091 to 0.0130 in.)
No. 2 0.35 to 0.45 mm (0.0138 to 0.0177 in.)
Oil (Side rail) 0.10 to 0.40 mm (0.0039 to 0.0157 in.)
Maximum
No. 1 0.40 mm (0.0157 in.)
No. 2 0.50 mm (0.0197 in.)
Oil (Side rail) 0.45 mm (0.0177 in.)
Piston ring groove clearance
No. 1 0.020 to 0.070 mm (0.0008 to 0.0028 in.)
No. 2 0.020 to 0.060 mm (0.0008 to 0.0024 in.)
Oil 0.020 to 0.070 mm (0.0008 to 0.0028 in.)
Piston ring end gap
Standard
No. 1 0.23 to 0.33 mm (0.0091 to 0.0130 in.)
No. 2 0.35 to 0.45 mm (0.0138 to 0.0177 in.)
Oil (Side rail) 0.10 to 0.40 mm (0.0039 to 0.0157 in.)
Maximum
No. 1 0.40 mm (0.0157 in.)
No. 2 0.50 mm (0.0197 in.)
Oil (Side rail) 0.45 mm (0.0177 in.)

Crankshaft pulley 250 Nm (2549 kgf-cm, 184 ft lb)