Part 3

Continue

ON malfunction (E)





- When either condition below is met: Condition (1) or (2)

Condition (1)

When one of the following conditions is met: Condition (a), (b), (c), (d), (e), (f), (g) or (h)

Condition (a)





Condition (b)





Condition (c)





Condition (d)





Condition (e)





Condition (f)





Condition (g)





Condition (h)






ON malfunction (F)





- When either condition below is met: Condition (1) or (2)

Condition (1)

When one of the following conditions is met: Condition (a), (b), (c), (d), (e), (f), (g) or (h)

Condition (a)





Condition (b)





Condition (c)





Condition (d)





Condition (e)





Condition (f)





Condition (g)





Condition (h)






TYPICAL MALFUNCTION THRESHOLDS

OFF malfunction
- When one of following conditions is met: OFF malfunction (A), (B), (C), (D) or (E)

OFF malfunction (A)

When either condition below is met: Condition (1) or (2)

Condition (1)





Condition (2)






ON malfunction
- When one of following conditions is met: ON malfunction (A), (B), (C), (D), (E) or (F)
2 detections are necessary per driving cycle:
1st detection: temporary flag ON
2nd detection: pending fault code ON

ON malfunction (A), (B) and (C)

When either condition below is met: Condition (1) or (2)

Condition (1)





Condition (2)






INSPECTION PROCEDURE

PROCEDURE

1. CHECK DTC OUTPUT (IN ADDITION TO DTC P0771, P0796, P2714 AND P2808)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / ECT / Trouble Codes.
(e) Read the DTCs using the Techstream.
Result:





HINT:
If any other codes besides P0771, P0776 and P2714 are output, perform troubleshooting for those DTCs first.

D -- Go to DTC Chart Diagnostic Trouble Code Descriptions
C -- CLEAR DTC AND PERFORM STALL SPEED TEST
B -- CLEAR DTC AND PERFORM STALL SPEED TEST
A -- Continue to next step.
2. CLEAR DTC AND PERFORM STALL SPEED TEST
(a) Clear the DTCs DTC Check / Clear.
HINT:
Write down the currently output DTCs before clearing them.
(b) Perform the stall speed test Mechanical System Tests.
Result:





ON malfunction (C)





- When either condition below is met: Condition (1) or (2)

Condition (1)

When one of the following conditions is met: Condition (a), (b), (c), (d), (e), (f), (g) or (h)

Condition (a)





Condition (b)





Condition (c)





Condition (d)





Condition (e)





Condition (f)





Condition (g)





Condition (h)






ON malfunction (D)





- When either condition below is met: Condition (1) or (2)

Condition (1)

When one of the following conditions is met: Condition (a), (b), (c), (d), (e), (f), (g) or (h)

Condition (a)





Condition (b)





Condition (c)





Condition (d)





Condition (e)





Condition (f)





Condition (g)





Condition (h)






ON malfunction (E)





- When either condition below is met: Condition (1) or (2)

Condition (1)

When one of the following conditions is met: Condition (a), (b), (c), (d), (e), (f), (g) or (h)

Condition (a)





Condition (b)





Condition (c)





Condition (d)





Condition (e)





Condition (f)





Condition (g)





Condition (h)






ON malfunction (F)





- When either condition below is met: Condition (1) or (2)

Condition (1)

When one of the following conditions is met: Condition (a), (b), (c), (d), (e), (f), (g) or (h)

Condition (a)





Condition (b)





Condition (c)





Condition (d)





Condition (e)





Condition (f)





Condition (g)





Condition (h)






TYPICAL MALFUNCTION THRESHOLDS

OFF malfunction
- When one of following conditions is met: OFF malfunction (A), (B), (C), (D) or (E)

OFF malfunction (A)

When either condition below is met: Condition (1) or (2)

Condition (1)





Condition (2)






ON malfunction
- When one of following conditions is met: ON malfunction (A), (B), (C), (D), (E) or (F)
2 detections are necessary per driving cycle:
1st detection: temporary flag ON
2nd detection: pending fault code ON

ON malfunction (A), (B) and (C)

When either condition below is met: Condition (1) or (2)

Condition (1)





Condition (2)






INSPECTION PROCEDURE

PROCEDURE

1. CHECK DTC OUTPUT (IN ADDITION TO DTC P0771, P0796, P2714 AND P2808)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / ECT / Trouble Codes.
(e) Read the DTCs using the Techstream.
Result:





HINT:
If any other codes besides P0771, P0776 and P2714 are output, perform troubleshooting for those DTCs first.

D -- Go to DTC Chart Diagnostic Trouble Code Descriptions
C -- CLEAR DTC AND PERFORM STALL SPEED TEST
B -- CLEAR DTC AND PERFORM STALL SPEED TEST
A -- Continue to next step.
2. CLEAR DTC AND PERFORM STALL SPEED TEST
(a) Clear the DTCs DTC Check / Clear.
HINT:
Write down the currently output DTCs before clearing them.
(b) Perform the stall speed test Mechanical System Tests.
Result: