Power Window Motor: Service and Repair

POWER WINDOW REGULATOR MOTOR

Power Window Regulator Motor:

REMOVAL

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
3. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
4. REMOVE COURTESY LIGHT ASSEMBLY
5. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
6. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP
7. REMOVE FRONT DOOR SERVICE HOLE COVER
8. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
9. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
10. REMOVE FRONT POWER WINDOW REGULATOR MOTOR

a. Using a "torx" socket wrench (T25), remove the 3 screws and the front power window regulator motor.

11. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
12. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
13. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
14. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP
15. REMOVE REAR DOOR SERVICE HOLE COVER
16. REMOVE REAR DOOR GLASS RUN
17. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
18. REMOVE REAR DOOR QUARTER WINDOW GLASS
19. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
20. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
21. REMOVE REAR POWER WINDOW REGULATOR MOTOR

a. Using a "torx" socket wrench (T25), remove the 3 screws and the rear power window regulator motor.

INSTALLATION

1. INSTALL FRONT POWER WINDOW REGULATOR MOTOR

NOTICE: The regulator arm must be below the intermediate position when installing the power window regulator motor.

a. Using a "torx" socket wrench (T25), install the front power window regulator motor with the 3 screws.

Torque: 5.4 N.m (55 kgf.cm, 48 in.lbf)

HINT: The new front window regulator adopts a self-tapping method. The installation position of regulator will be threaded when the self-tapping screw is inserted.

2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
4. INSTALL FRONT DOOR SERVICE HOLE COVER
5. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP
6. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
7. INSTALL COURTESY LIGHT ASSEMBLY
8. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
9. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG
10. INSTALL REAR POWER WINDOW REGULATOR MOTOR

NOTICE: The regulator arm must be below the intermediate position when installing the power window regulator motor.

a. Using a "torx" socket wrench (T25), install the rear power window regulator motor with the 3 screws.

Torque: 5.4 N.m (55 kgf.cm, 48 in.lbf)

HINT: The new rear window regulator adopts a self-tapping method. The installation position of regulator will be threaded when the self-tapping screw is inserted.

11. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
12. INSTALL REAR DOOR GLASS SUB-ASSEMBLY
13. INSTALL REAR DOOR QUARTER WINDOW GLASS
14. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
15. INSTALL REAR DOOR GLASS RUN
16. INSTALL REAR DOOR SERVICE HOLE COVER
17. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP
18. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
19. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
20. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG
21. CONNECT BATTERY NEGATIVE TERMINAL
22. PERFORM INITIALIZATION Initialization

NOTICE: Some systems need initialization after reconnecting the cable to the negative battery terminal.