P0171
DTC P0171 SYSTEM TOO LEAN (FUEL TRIM) (BANK 1)CIRCUIT DESCRIPTION
DTC Detection Condition:
The fuel trim is related to the feedback compensation value, not to the basic injection time.The fuel trim includes the short-term fuel trim and the long-term fuel trim.
The short-term fuel trim is the short-term fuel compensation used to maintain the air-fuel ratio at stoichiometric air-fuel ratio. The signal from the Heated Oxygen Sensor (HO2S) indicates whether the air-fuel ratio is RICH or LEAN compared to the stoichiometric air-fuel ratio. This variance triggers a reduction in the fuel volume if the air-fuel ratio is RICH, and an increase in the fuel volume if it is LEAN.
The short-term fuel trim varies from the central value due to individual engine differences, vehicle wear and changes in the operating environment. The long-term fuel trim, which controls overall fuel compensation, steadies long-term deviations of the short-term fuel trim from the central value.
If both the short-term fuel trim and the long-term fuel trim are LEAN or RICH beyond a certain value, the ECM determines this as a malfunction, illuminates the MIL and sets a DTC.
HINT:
- When DTC P0171 or P0174 is recorded, the actual air-fuel ratio is on the LEAN side.When DTC P0172 or P0175 is recorded, the actual air-fuel ratio is on the RICH side.
- If the vehicle runs out of fuel, the air-fuel ratio is LEAN and DTC P0171 or P0174 may be recorded.The MIL is then illuminated.
- If the total of the short-term fuel trim value and long-term fuel trim value is within the malfunction threshold (and ECT is more than 75 °C (167 °F)), the system is functioning normally.
MONITOR DESCRIPTION
Monitor Strategy:
Typical Enabling Conditions:
Typical Malfunction Thresholds:
Under closed-loop fuel control, fuel injection amounts that deviate from the ECM's estimated fuel amount will cause a change in the long-term fuel trim compensation value.Long-term fuel trim value is adjusted when persistent deviations in the short-term fuel trim's value are present. Also, the smoothed fuel trim learning value is adjusted when deviations from the ECM's simulated fuel injection value are present. The smoothed fuel trim learning value is the combination of smoothed short-term fuel trim (fuel feedback compensation value.and smoothed long-term fuel trim (learning value of the air-fuel ratio). When the smoothed fuel trim learning value exceeds the malfunction threshold, the ECM interprets this as a fault in the fuel system and sets a DTC.
Example: The smoothed fuel trim learning value is above 40 % or below -35 %. The ECM interprets this as a fault in the fuel system.
Wiring Diagram:
Step 1 - 3:
Step 4:
Step 5 - 9:
Step 10 - 12:
Step 13 - 14:
Step 15:
INSPECTION PROCEDURE
HINT: It is possible to find the malfunctioning area using the ACTIVE TEST A/F CONTROL operation. The ACTIVE TEST can determine if the HO2S or other potential trouble areas are malfunctioning or not. The injection volume can be switched to -12.5 % (decrease.or +25 % (increase.by the ACTIVE TEST. The ACTIVE TEST procedure enables a technician to check and graph the voltage outputs of the HO2Ss.
Procedure:
a. Connect the hand-held tester to the DLC3.
b. Turn the ignition switch ON.
c. Warm up the engine by running the engine at 2,500 rpm for approximately 90 seconds.
d. Enter the following menus: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL.
e. Perform the ACTIVE TEST while the engine is idling.
Standard:
The HO2S reacts in accordance with the increase and decrease of injection volume:
+25 % ->RICH output: more than 0.55 V
-12.5 %->LEAN output: Less than 0.4 V
NOTE: The HO2S (sensor 1.output has a few seconds of delay and the HO2S (sensor 2.output has a maximum of 20 seconds of delay.
If the vehicle is short on fuel, the air-fuel ratio becomes LEAN and the DTCs will be recorded.
HINT: Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when a malfunction is detected.When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was LEAN or RICH, and other data from the time the malfunction occurred.
A high HO2S (sensor 1.voltage (0.55 V or more.indicates a RICH air-fuel ratio.
A low HO2S (sensor 1.voltage (0.4 V or less) indicates a LEAN air-fuel ratio.
CHECK FOR INTERMITTENT PROBLEMS
HINT: Inspect the vehicle's ECM using check mode. Intermittent problems are easier to detect when the hand-held tester is in check mode. In check mode, the hand-held tester uses 1 trip detection logic, which has a higher sensitivity to malfunctions than normal mode (default), which uses 2 trip detection logic.
a. Clear the DTCs
b. Set the check mode
c. Perform a simulation test.
d. Check the connector and terminal
e. Wiggle the harness and the connector