Diagnosis System

DIAGNOSIS SYSTEM

a. Description
- When troubleshooting OBD II vehicles, the only difference from the usual troubleshooting procedure is that you need to connect the vehicle to the OBD II scan tool complying with SAE J1978 or LEXUS hand-held tester, and read off various data output from the vehicle's ECM.




- OBD II regulations require that the vehicle's on-board computer lights up the Malfunction Indicator Light (MIL) on the instrument panel when the computer detects a malfunction in the emission control system/components or in the powertrain control components which affect vehicle emissions, or a malfunction in the computer. In addition to the MIL lighting up when a malfunction is detected, the applicable Diagnostic Trouble Codes (DTCs) pre scribed by SAE J2012 are recorded in the ECM memory.
If the malfunction does not reoccur in 3 consecutive trips, the MIL goes off automatically but the DTC remains recorded in the ECM memory.




- To check the DTC, connect the OBD II scan tool or LEXUS hand-held tester to the Data Link Connector 3 (DLC3) of the vehicle. The OBD II scan tool or LEXUS hand-held tester also enables you to erase the DTC and check freeze frame data and various forms of engine data (For operating instructions, see the OBD II scan tool's instruction book.). DTC includes SAE controlled codes and manufacturer controlled codes. SAE controlled codes must be set as prescribed by the SAE, while manufacturer controlled codes can be set freely by a manufacturer within the prescribed limits.

- The diagnosis system operates in normal mode during normal vehicle use. It also has a check mode for technicians to simulate malfunction symptoms and troubleshoot it. Most DTC use the 2 trip detection logic* to prevent an erroneous detection, and ensure the malfunction detection. By switching the ECM to check mode when troubleshooting, a technician can cause the MIL to light up for a malfunction that is only detected once or momentarily (LEXUS hand-held tester only).

- *2 trip detection logic:
When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory. (1st trip)
If the same malfunction is detected again during the second drive test, this second detection causes the MIL to light up. (2nd trip). The 2 trip repeats the same mode twice (However, the ignition switch must be turned OFF between the 1st trip and 2nd trip.).

- Freeze frame data:
Freeze frame data records the engine condition when a misfire (DTCs P0300 - P0308) or fuel trim malfunction (DTCs P0171, P0172, P0174 and P0175) or other malfunction (first malfunction only), is detected, as freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when the malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was lean or rich, etc. at the time of the malfunction.

Priorities for troubleshooting:
If troubleshooting priorities for multiple DTCs are given in the applicable DTC chant, these should be followed.
If no instructions are given, troubleshoot DTCs according to the following priorities.
1. DTC other than fuel trim malfunction (DTCs P0171, P0172, P0174 and P0175), and misfire (DTCs P0300 - P0308).
2. Fuel trim malfunction (DTCs P0171, P0172, P0174 and P0175).
3. Misfire (DTCs P0300 - P0308).







b. Check the DLC3.
The vehicle's ECM uses ISO 9141-2 for communication. The terminal arrangement of the DLC3 complies with SAE J1962 and matches the ISO 9141-2 format.

HINT: If your display shows UNABLE TO CONNECT TO VEHICLE when you have connected the cable of the OBD II scan tool or LEXUS hand-held tester to the DLC3, turned the ignition switch ON and operated the scan tool, there is a problem on the vehicle side or tool side.
- If the communication is normal when the tool is connected to another vehicle, inspect the DLC3 on the original vehicle.
- If the communication is still impossible when the tool is connected to another vehicle, the problem is probably in the tool itself, so consult the Service Department listed in the tool's instruction manual.