Rear Seat (RH)
DISASSEMBLY1. REMOVE HEADRESTS
2. REMOVE RECLINING COVER PROTECTORS
Using a screwdriver, remove the reclining cover protectors.
HINT: Tape the screwdriver tip before use.
3. REMOVE SEAT CUSHION ASSEMBLY
Remove the 4 bolts and seat cushion assembly.
4. REMOVE SEAT CUSHION COVER
a. Remove the 3 screws and cup holder.
b. Remove the cup holder bezel.
c. Remove the hog rings and seat cushion cover with pad from the seatback frame.
d. Remove the hog rings and seat cushion cover from the seat cushion pad.
5. REMOVE SEATBACK ASSEMBLY
a. Remove the bolt and rear seat outer center belt anchor.
b. Remove the reclining covers.
c. Disconnect the seat lock control cable.
d. Remove the 4 bolts and seatback assembly.
6. REMOVE ARMREST ASSEMBLY
a. Remove the screw and armrest cover.
b. Remove the bolt and armrest assembly.
7. REMOVE SEATBACK COVER
a. Remove the inner shield.
b. Remove the 2 screws.
c. Using a screwdriver, remove the seatback board.
HINT: Tape the screwdriver tip before use.
d. Using a screwdriver, remove the cover, then remove the 2 seat lock control lever set screws.
HINT: Tape the screwdriver tip before use.
e. Disconnect the seat lock control cable from the lever.
f. Remove the headrest supports.
g. Remove the rear seat outer center belt shoulder cover.
h. Disengage the seatback cover hooks and remove the seatback cover with pad from the seatback frame.
i. Remove the armrest pad and armrest pad LH from the seatback frame.
j. Remove the 2 bolts and armrest bracket from the seatback frame.
k. Remove the hog rings and seatback cover from the seatback pad.
l. Remove the screw and disconnect the seat lock control cable.
8. REMOVE REAR SEAT OUTER CENTER BELT
Remove the nut and retractor of rear seat outer center belt.
9. REMOVE REAR SEAT CUSHION SHIELD
Remove the screw and rear seat cushion shield.
10. REMOVE REAR SEAT INNER CUSHION COVER
Remove a screw and rear seat inner cushion cover.
11. REMOVE REAR SEAT INNER BELT
Remove the bolt and rear seat inner belt.
12. REMOVE SLIDING HANDLE
13. REMOVE RECLINING CONNECTING ROD
Remove the 4 bolts and reclining connecting rod.
14. REMOVE RECLINING CONNECTING PIPE AND LOWER SEATBACK FRAME
REASSEMBLY
1. INSTALL RECLINING CONNECTING PIPE AND LOWER SEATBACK FRAME
a. Adjust the reclining lock positions of the seat adjusters.
b. Slide the seat adjusters to the front most position.
c. Place the adjusters on a spacer to adjust the seat rails in parallel and install the connecting pipe and lower seat-back frame.
HINT: When installing the connecting pipe with raising up the adjusters, the lock positions adjusted in 1-(a) step slip off, then lock error will occur.
2. INSTALL RECLINING CONNECTING ROD
Install the reclining connecting rod with the 4 bolts.
Torque: 18 N.m (184 kgf.cm, 13 ft.lbf)
3. INSTALL SLIDING HANDLE
4. INSTALL REAR SEAT INNER BELT
Install the rear seat inner belt with the bolt.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
5. INSTALL REAR SEAT INNER CUSHION COVER
Install the rear seat inner cushion cover with the screw.
6. INSTALL REAR SEAT CUSHION SHIELD
Install the rear seat cushion shield with the screw.
7. INSTALL REAR SEAT OUTER CENTER BELT
Install the retractor of rear seat outer center belt with the nut.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
8. INSTALL SEATBACK COVER
a. Install the seat lock control cable with the screw.
b. Install the seatback cover with the new hog rings to the seatback pad.
HINT: When installing hog ring, take care to prevent wrinkles as much as possible.
c. Install the 2 screws and armrest bracket to the seatback frame.
d. Install the armrest pad and armrest pad LH to the seat-back frame.
e. Install the seatback cover with pad to the seatback frame and engage the seatback cover hooks.
f. Install the rear seat outer center belt shoulder cover.
g. Install the headrest supports.
h. Connect the seat control cable to the seat lock control lever.
i. Install the seat lock control lever with the 2 screws, then install the cover.
j. Install the seatback board with the 2 screws.
k. Install the inner shield.
9. INSTALL ARMREST ASSEMBLY
a. Install the armrest assembly with the bolt.
Torque: 18 N.m (184 kgf.cm, 13 ft.lbf)
b. Install the armrest cover with the screw.
10. INSTALL SEATBACK ASSEMBLY
a. Install the seatback assembly with the 4 nuts.
Torque: 55 N.m (560 kgf.cm, 41 ft.lbf)
b. Connect the seatback lock control cable.
c. Install the reclining covers.
d. Install the rear seat outer center belt anchor with the bolt.
Torque: 42 N.m (430 kgf.cm, 31 ft.lbf)
11. INSTALL SEAT CUSHION COVER
a. Install the seat cushion cover with the new hog rings to the seat cushion pad.
b. Install the seat cushion cover with pad to the seatback frame with the new hog rings.
HINT: When installing hog rings, take care to prevent wrinkles as much as possible.
c. Install the cup holder bezel.
d. Install the cup holder with the 3 screws.
12. INSTALL SEAT CUSHION ASSEMBLY
Install the seat cushion assembly with the 4 bolts.
Torque:
Upper bolt: 37 N.m (375 kgf.cm, 27 ft.lbf)
Lower bolt: 18 N.m (184 kgf.cm, 13 ft.lbf)
13. INSTALL RECLINING COVER PROTECTORS
14. INSTALL HEADRESTS