Rear Seat

Replacement

Rear Seat Assembly Replacement
1. Loosen the mounting bolt.
2. Push the lock pin (B), remove the rear seat cushion (A).

Tightening torque :
16.7 - 25.5 N.m (1.7 - 2.6 kgf.m, 12.3 - 18.8 lb-ft)




3. After loosening the mounting bolt, then remove the center rear seat belt lower anchor (A).

Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.9 - 39.8 lb-ft)




4. After loosening the mounting bolts, then remove the rear seat back (A).

Tightening torque :
16.7 - 25.5 N.m (1.7 - 2.6 kgf.m, 12.3 - 18.8 lb-ft)




5. Installation is the reverse of removal.

Rear Seat Back Cover Replacement [LH]

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
- Put on gloves to protect your hands.

1. Remove the following items first :
A. Rear seat back assembly [LH]
2. Push the lock pin (B), remove the headrest (A).




3. Remove the rear seat folding knob (A) after turning in the counter clock-wise direction.
4. Remove the rear back bezel (B).




5. Using a screwdriver or remover, remove the center seat belt cover (A).




6. Using a screwdriver or remover, remove the tether anchor garnish (A).




7. Remove the rear seat back lower mounting protector (A).




8. Zip off the rear seat back cover (A), and then full it up.




9. Pull out the headrest guides (A) while pinching the end of the guides, and remove them.




10. Remove the rear seat back cover from the rear seat back frame.
11. After removing the hog-ring clips (B) on the rear of seat back and remove the rear seat back cover (A).




12. Installation is the reverse of removal.

NOTE:
- To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
- Replace the hog ring clips with new ones using special tool [C (09880-4F000)].





Rear Seat Latch Replacement [LH]

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
- Put on gloves to protect your hands.

1. Remove the following items first :
A. Rear seat back assembly [LH]
B. Rear seat back cover [LH]
2. After loosening the mounting bolts, then remove the rear seat latch assembly (A).

Tightening torque :
19.6 - 29.4 N.m (2.0 - 3.0 kgf.m, 14.5 - 21.7 lb-ft)




3. Installation is the reverse of removal.

Rear Seat Back Cover Replacement [RH]

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
- Put on gloves to protect your hands.

1. Remove the following items first :
A. Rear seat back assembly [RH]
2. Push the lock pin (B), remove the headrest (A).




3. Remove the rear seat folding knob (A) after turning in the counter clock-wise direction.
4. Remove the rear back bezel (B).




5. Using a screwdriver or remover, remove the tether anchor garnish (A).




6. Remove the rear seat back lower mounting protector (A).




7. Zip off the rear seat back cover (A), and then full it up.




8. Pull out the headrest guides (A) while pinching the end of the guides, and remove them.




9. Remove the rear seat back cover from the rear seat back frame.
10. After removing the hog-ring clips (B) on the rear of seat back and remove the rear seat back cover (A).




11. Installation is the reverse of removal.

NOTE:
- To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
- Replace the hog ring clips with new ones using special tool [C (09880-4F000)].





Rear Seat Latch Replacement [RH]

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
- Put on gloves to protect your hands.

1. Remove the following items first :
A. Rear seat back assembly [RH]
B. Rear seat back cover [RH]
2. After loosening the mounting bolts, then remove the rear seat latch assembly (A).

Tightening torque :
19.6 - 29.4 N.m (2.0 - 3.0 kgf.m, 14.5 - 21.7 lb-ft)




3. Installation is the reverse of removal.

Rear Seat Cushion Cover Replacement

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts your hands.
- Put on gloves to protect your hands.

1. Remove the following items first :
A. Rear seat cushion assembly
2. Remove the hog-ring clips (A).




3. After removing the hog-ring clips (B) on the rear of seat cushion and remove the rear seat cushion cover (A).




4. Installation is the reverse of removal.

NOTE:
- To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
- Replace the hog ring clips with new ones using special tool [C (09880-4F000)].