Rear Seat Belt

Replacement

Rear Seat Belt Replacement
[5 Door]

CAUTION:
- When installing the belt, make sure not to damaged the retractor.

1. Remove the following items first :
A. Rear seat assembly

B. Rear door scuff trim

2. Using a screwdriver or remover, remove the rear transverse trim (A).




3. After loosening the mounting bolt, then remove the rear seat belt lower anchor (A).

Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.8 - 39.8 lb-ft)




4. After loosening the mounting blots, then remove the rear seat bracket (A).




5. Using a screwdriver or remover, remove the lamp (A).
6. Disconnect the lamp connector (B).




7. After loosening the mounting screws, then remove the luggage side trim (A).




8. Remove the rear seat belt upper anchor cover (B).
9. Using a screwdriver or remover, remove the rear pillar trim (A).




10. After loosening the mounting bolt, then remove the rear seat belt (A) and rear seat belt retractor (B).

Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.8 - 39.8 lb-ft)




11. Installation is the reverse of removal.

NOTE:
- Replace any damaged clips.
- Make sure the connectors are plugged in properly.

[4 Door]

CAUTION:
- When installing the belt, make sure not to damaged the retractor.

1. Remove the rear seat assembly.

2. Using a screwdriver or remover, remove the rear pillar trim (A).




3. After loosening the mounting screws, then remove the rear door scuff trim (A).




4. After loosening the mounting bolt, then remove the rear seat belt lower anchor (A).

Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.8 - 39.8 lb-ft)




5. After loosening the mounting blots, then remove the rear seat folding bracket (A).




6. After loosening the mounting clips and screws, then remove the luggage partition trim (A).




7. After loosening the mounting clips and screw, then remove the rear wheel housing trim (A).




8. Disconnect the high mounted stop lamp connector (A).




9. Remove the rear seat belt upper anchor cover (A).




10. Remove the rear package tray trim (A).




11. After loosening the retractor (B) mounting bolts, then remove the rear seat belt (A).
[LH, RH]

Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.9 - 39.8 lb-ft)




[Center]

Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.9 - 39.8 lb-ft)




12. Installation is the reverse of removal.

NOTE:
- Make sure the connectors are connected in properly.
- Replace any damage clips.

Center Rear Seat Belt
[5 Door]
1. Remove the following items first :
A. Rear seat back assembly [LH]

B. Rear seat back cover [LH]

2. After loosening the mounting nut, then remove the center rear seat belt retractor (A).

Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.8 - 39.8 lb-ft)




3. Installation is the reverse of removal.

NOTE:
- Replace any damaged clips.

Rear Seat Belt Buckle Replacement
1. Remove the following items first :
A. Rear seat cushion assembly

2. Disconnect the rear seat buckle connector (B).
3. After loosening the mounting bolt, then remove the rear seat belt buckle (A).

[LH]

Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.9 - 39.8 lb-ft)

[A Type]




[B Type]




[C Type]





[RH]

Tightening torque :
39.2 - 53.9 N.m (4.0 - 5.5 kgf.m, 28.9 - 39.8 lb-ft)

[A Type]




[B Type]




[C Type]




4. Installation is the reverse of removal.