Parking Brake Pedal: Service and Repair
Removal
Parking Brake Pedal [Foot type]
1. Turn ignition OFF and disconnect the negative (-) battery cable.
2. Remove the crash pad lower panel and reinforcing panel.
3. Remove the junction box.
4. Disconnect the parking brake switch connector (A).
5. Remove the parking brake cable mounting nut (A).
6. Remove the parking brake pedal mounting bolts (A) and nuts (B).
7. Remove the parking brake cable adjusting nut (A) and the fixing clip (B), and then remove the parking brake pedal.
8. Remove the floor console.
9. Remove the shift lever assembly.
10. Remove the paring brake cable (B) after removing the cable retainer (A).
11. Remove the parking brake cable fixing clip (A) and bolts (B). And then remove the front parking brake cable.
12. Raise the vehicle, and make sure it is securely supported.
13. Remove the parking brake cable (B) after removing the fixing clip (A).
14. Loosen the parking brake cable bracket bolts and remove the rear parking brake cable.
Parking Brake Lever [Hand type]
1. Remove the floor console.
2. Disconnect the parking brake switch connector (A).
3. Remove the parking brake cable (B) after removing the cable retainer (A).
4. Remove the parking brake lever assembly after removing the bolts (A) as shown below.
5. Raise the vehicle and make sure it is securely supported.
6. Remove the rear wheel & tire.
Tightening torque:
88.3 - 107.9 N.m (9.0 - 11.0 kgf.m, 65.1 - 79.6 lb-ft)
7. Remove the parking brake cable (B) after removing the fixing clip (A).
8. Loosen the parking brake cable bracket bolts and remove the parking brake cable.
Installation
Parking Brake Lever [Hand Type]
1. Install the parking brake lever assembly, then tighten the mounting bolts.
Tightening torque:
19.6 - 29.4 N.m (2.0 - 3.0 kgf.m, 14.5 - 21.7 lb-ft)
2. Install the parking brake cable (B) and then cable retainer (A).
3. Apply a coating of the specified grease to each sliding parts (A) of the ratchet plate or the ratchet pawl.
Specified grease:
Multi purpose grease SAE J310, NLGI No.2
4. Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A).
Parking brake lever stroke:
4 clicks (Pull the lever with 20kgf)
NOTE:
After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke.
5. Release the parking brake lever fully, and check that parking brakes do not drag when the rear wheels are turned. Readjust if necessary.
6. Make sure that the parking brakes are fully applied when the parking brake lever is pulled up fully.
7. Reconnect the connector of parking brake switch.
NOTE:
Inspect the continuity of parking brake switch.
When the brake lever is pulled: continuity
When the brake lever is released: no continuity
8. Install the floor console.
Parking Brake Pedal [Foot type]
1. Install the parking brake cable.
2. Install the shift lever assembly.
3. Install the floor console.
4. Install the holding clip (B) and the cable adjusting nut(A) after fixing the parking brake cable.
5. Install the parking brake pedal, and then install the parking brake pedal mounting bolts (A) and nuts (B).
Tightening torque:
9.8 - 14.7 N.m (1.0 - 1.5 kgf.m, 7.2 - 10.8 lb-ft)
6. Adjust the parking brake pedal stroke by turning the adjusting nut (A).
(1) Operate the parking brake pedal through a full stroke over 3 times for setting the parking cables.
(2) Adjust the adjusting nut (A) for parking brake pedal stroke 4 - 5notches when operating effort is 196N(20kgf.44lb).
CAUTION:
1. The parking brake adjustment must be carried out after adjusting the rear shoe.
2. After adjusting parking brake, notice following matter.
1) Must be free from clearance between adjusting nut and pin.
2) Check securely that the brake is not dragging.
7. Reconnect the parking brake switch connector(A).
8. Install the junction box.
9. Install the reinforcing panel and crash pad lower panel.