1 of Part 2

Replacement

Cluster Replacement

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Put on gloves to protect your hands.

1. Using a screwdriver or remover, remove the crash pad side cover (A).




2. After loosening the mounting screws, then remove the crash pad lower panel (A).




3. Disconnect the connectors (A).

[LH]





[RH]




4. After loosening the mounting screws, then remove the crash pad garnish [LH] (A).




5. Using a screwdriver or remover, remove the crash pad garnish [RH] (A).




6. After loosening the mounting screws, then remove the cluster fascia panel (A).




7. After loosening the mounting screws, then remove the cluster assembly (A).




8. Disconnect the connector (A).




9. Installation is the reverse of removal.

NOTE:
- Make sure the connectors are connected in properly.
- Replace any damaged clips.

Center Facia Upper Panel Replacement

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Put on gloves to protect your hands.

1. Using a screwdriver or remover, remove the crash pad side cover (A).




2. After loosening the mounting screws, then remove the crash pad lower panel (A).




3. Disconnect the connectors (A).

[LH]





[RH]




4. After loosening the mounting screws, then remove the crash pad garnish [LH] (A).




5. Using a screwdriver or remover, remove the crash pad garnish [RH] (A).




6. After loosening the mounting screws, then remove the cluster fascia panel (A).




7. After loosening the mounting screws, then remove the heater control unit (A).




8. Disconnect the connectors (A) and hose (B).




9. After loosening the mounting screws, then remove the center fascia upper panel (A).




10. Installation is the reverse of removal.

NOTE:
- Make sure the connectors are connected in properly.
- Replace any damaged clips.

Crash Pad Lower Panel Replacement

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Put on gloves to protect your hands.

1. Using a screwdriver or remover, remove the crash pad side cover (A).




2. After loosening the mounting screws, then remove the crash pad lower panel (A).




3. Disconnect the connectors (A).

[LH]





[RH]




4. Installation is the reverse of removal.

NOTE:
- Make sure the connectors are connected in properly.
- Replace any damaged clips.

Audio assembly Replacement

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Put on gloves to protect your hands.

1. Using a screwdriver or remover, remove the crash pad side cover (A).




2. After loosening the mounting screws, then remove the crash pad lower panel (A).




3. Disconnect the connectors (A).

[LH]





[RH]




4. After loosening the mounting screws, then remove the crash pad garnish [LH] (A).




5. Using a screwdriver or remover, remove the crash pad garnish [RH] (A).




6. After loosening the mounting screws, then remove the cluster fascia panel (A).




7. After loosening the mounting screws, then remove the heater control unit (A).




8. Disconnect the connectors (A) and hose (B).




9. After loosening the mounting screws, then remove the center fascia upper panel (A).




10. After loosening the mounting screws, then remove the audio assembly (A).




11. Disconnect the connectors.




12. Installation is the reverse of removal.

NOTE:
- Make sure the connectors are connected in properly.
- Replace any damaged clips.

Heater Control Unit Replacement

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Put on gloves to protect your hands.

1. Using a screwdriver or remover, remove the crash pad side cover (A).




2. After loosening the mounting screws, then remove the crash pad lower panel (A).




3. Disconnect the connectors (A).

[LH]





[RH]




4. Using a screwdriver or remover, remove the crash pad garnish [RH] (A).




5. After loosening the mounting screws, then remove the heater control unit (A).




6. Disconnect the connectors (A) and hose (B).




7. Installation is the reverse of removal.

NOTE:
- Make sure the connectors are connected in properly.
- Replace any damaged clips.