P2128
P2127, P2128 APP SENSOR
Description
The accelerator pedal position sensor is installed on the upper end of the accelerator pedal assembly. The sensor detects the accelerator position and sends a signal to the ECM.
Accelerator pedal position sensor has two sensors. These sensors are a kind of potentiometer which transform the accelerator pedal position into output voltage, and emit the voltage signal to the ECM.
The ECM judges the current opening angle of the accelerator pedal from these signals and controls the throttle control motor based on these signals.
Idle position of the accelerator pedal is determined by the ECM
receiving the signal from the accelerator pedal position sensor. The
ECM uses this signal for engine operations such as fuel cut.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
1.Turn ignition switch OFF and wait at least 10 seconds.
2.Turn ignition switch ON.
3.Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.
- GO TO 2.
2. PERFORM DTC CONFIRMATION PROCEDURE
1.Start engine and let it idle for 1 second.
2.Check DTC.
Is DTC detected?
YES- Go to "Diagnosis Procedure" .
NO- INSPECTION END
Diagnosis Procedure
1. CHECK GROUND CONNECTION
1.Turn ignition switch OFF.
2.Check ground connection M95. Refer to Ground Inspection in "Circuit Inspection" Circuit Inspection.
Is the inspection result normal?
YES- GO TO 2.
NO- Repair or replace ground connection.
2. CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-I
1.Disconnect accelerator pedal position (APP) sensor harness connector.
2.Turn ignition switch ON.
3.Check the voltage between APP sensor harness connector and ground.
Is the inspection result normal?
YES- GO TO 7.
NO- GO TO 3.
3. CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-II
1.Turn ignition switch OFF.
2.Disconnect ECM harness connector.
3.Check the continuity between APP sensor harness connector and ECM harness connector.
Is the inspection result normal?
YES- GO TO 5.
NO- GO TO 4.
4. DETECT MALFUNCTIONING PART
Check the following.
- Harness connectors M6, E106
- Harness for open or short between ECM and accelerator pedal position sensor
- Repair open circuit.
5. CHECK SENSOR POWER SUPPLY CIRCUIT
Check harness for short to power and short to ground, between the following terminals.
Is the inspection result normal?
YES- GO TO 6.
NO- Repair short to ground or short to power in harness or connectors.
6. CHECK COMPONENTS
Check the following.
- Crankshaft position sensor (POS) (Refer to "Component Inspection" P0335.)
- Brake booster pressure sensor (Refer to "Component Inspection" P0555.)
- EVAP control system pressure sensor (Refer to "Component Inspection" P0451.)
- Refrigerant pressure sensor (Refer to "Diagnosis Procedure" Refrigerant Pressure Sensor.)
Is the inspection result normal?
YES- GO TO 13.
NO- Replace malfunctioning component.
7. CHECK APP SENSOR 2 GROUND CIRCUIT FOR OPEN AND SHORT
1.Turn ignition switch OFF.
2.Disconnect ECM harness connector.
3.Check the continuity between APP sensor harness connector and ECM harness connector.
4.Also check harness for short to ground and short to power.
Is the inspection result normal?
YES- GO TO 9.
NO- GO TO 8.
8. DETECT MALFUNCTIONING PART
Check the following.
- Harness connectors M6, E106
- Harness for open or short between ECM and accelerator pedal position sensor
- Repair open circuit, short to ground or short to power in harness or connectors.
9. CHECK APP SENSOR 2 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.Check the continuity between APP sensor harness connector and ECM harness connector.
2.Also check harness for short to ground and short to power.
Is the inspection result normal?
YES- GO TO 11.
NO- GO TO 10.
10. DETECT MALFUNCTIONING PART
Check the following.
- Harness connectors M6, E106
- Harness for open or short between ECM and accelerator pedal position sensor
- Repair open circuit, short to ground or short to power in harness or connectors.
11. CHECK APP SENSOR
Refer to "Component Inspection" .
Is the inspection result normal?
YES- GO TO 13.
NO- GO TO 12.
12. REPLACE ACCELERATOR PEDAL ASSEMBLY
1.Replace accelerator pedal assembly. Refer to "Exploded View" Exploded View.
2.Go to "Special Repair Requirement" .
- INSPECTION END
13. CHECK INTERMITTENT INCIDENT
Refer to "Circuit Inspection" Circuit Inspection.
- INSPECTION END
Component Inspection
1. CHECK ACCELERATOR PEDAL POSITION SENSOR
1.Turn ignition switch OFF.
2.Reconnect all harness connectors disconnected.
3.Turn ignition switch ON.
4.Check the voltage ECM harness connector terminals as per the following.
Is the inspection result normal?
YES- INSPECTION END
NO- GO TO 2.
2. REPLACE ACCELERATOR PEDAL ASSEMBLY
1.Replace accelerator pedal assembly. Refer to "Exploded View" Exploded View.
2.Go to "Special Repair Requirement" P2122.
- INSPECTION END
Special Repair Requirement
1. PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
Refer to "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Requirement" Special Repair Requirement.
- GO TO 2.
2. PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Refer to "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement" Special Repair Requirement.
- GO TO 3.
3. PERFORM IDLE AIR VOLUME LEARNING
Refer to "IDLE AIR VOLUME LEARNING : Special Repair Requirement" Special Repair Requirement.
- END