Repair Procedures

Inspection

Smart Key Unit
- Refer to the BE group - inspection / self diagnosis with scan tool.

Smart Key Switch
- Refer to the BE group - inspection / self diagnosis with scan tool.

Antenna
- Refer to the BE group - inspection / self diagnosis with scan tool.

Trunk Lid Open Switch
1. Remove the trunk trim.

2. Check for continuity between the Trunk actuator terminals.




3. If continuity is not specified, inspect the switch






Removal

Smart key unit
1. Disconnect the negative(-) battery terminal.
2. Remove the glove box(A).





3. Remove the glove box housing(A) after loosening the mounting screws.




4. Loosen the nuts(2EA) from the smart key unit(A) after disconnecting the connector.





RF Receiver
1. Disconnect the negative(-) battery terminal.
2. Remove the glove box(A).





3. Remove the glove box housing(A) after loosening the mounting screws.




4. Disconnect the connector after loosening the RF receiver(A) nut(1EA).





Interior 1 Antenna
1. Disconnect the negative(-) battery terminal.
2. Remove the console upper cover(A).





3. Remove the center fascia lower panel(A).




4. Loosen the interior 1 antenna(A) screws(2EA) located in front of the console.




5. Remove the interior 1 antenna(A) after disconnect the connector.





Interior 2 Antenna
1. Disconnect the negative(-) battery terminal.
2. Remove the console rear cover(A).





3. Disconnect the interior 2 antenna connector located at the console rear side, then remove the interior 2 antenna(A) after loosening screws(2EA).





Interior 3 Antenna
1. Disconnect the negative(-) battery terminal.
2. Remove the trunk panel(A) after loosening the mounting screws.




3. Disconnect the interior 2 antenna connector(A) and remove the interior 3 antenna(B) after loosening nut(2EA).





Exterior Bumper Antenna
1. Disconnect the negative(-) battery terminal.
2. Remove the rear bumper.

3. Disconnect the antenna connector(B) and remove the exterior bumper antenna(A) after loosening the nuts(2EA).





Buzzer
1. Disconnect the negative(-) battery terminal.
2. Remove the left side fender.

3. Remove the external buzzer(A).





Door Outside Handle
1. Disconnect the negative (-) battery terminal.
2. Disconnect the connector after removing the door trim.

3. After loosening the mounting bolt, then remove the key holder (A).




4. Remove the outside handle (A) by sliding it rearward.






Installation

Smart Key Unit
1. Install the smart key unit.
2. Install the smart key unit mounting nut and connector.
3. Install the glove box housing.
4. Install the glove box.
5. Install the negative (-) battery terminal and check the smart key system.

RF Receiver
1. Install the RF receiver.
2. Install the glove box housing.
3. Install the glove box.
4. Install the negative (-) battery terminal and check the smart key system.

Interior 1 Antenna
1. Install the interior 1 antenna.
2. Install the center fascia lower panel.
3. Install the console upper cover.
4. Install the negative (-) battery terminal and check the smart key system.

Interior 2 Antenna
1. Install the interior 2 antenna.
2. Install the console rear cover after connecting the connector.
3. Install the negative (-) battery terminal and check the smart key system.

Interior 3 Antenna
1. Install the interior 3 antenna.
2. Install the trunk panel.
3. Install the negative (-) battery terminal and check the smart key system.

Exterior Bumper Antenna
1. Install the exterior bumper antenna.
2. Install the rear bumper.
3. Install the negative (-) battery terminal and check the smart key system.

Buzzer
1. Install the buzzer.
2. Install the left side fender.
3. Install the negative (-) battery terminal and check the smart key system.

Door Outside Handle
1. Install the outside handle.
2. Install the door trim.
3. Install the negative (-) battery terminal and check the smart key system.