Reprogramming Procedure
NOTE:Verify that the vehicle is affected by identifying the vehicle production date and VIN.
AUTOMATIC UPDATE PROCEDURE:
1. Attach the DLC (Data Link Connector) cable to the Hi-Scan Pro main body and tighten the 2 bolts securely.
2. Remove the current system software card from the Hi-Scan Pro and insert the blue reprogramming software card (with the new ECM program) into the Hi-Scan Pro top slot.
3. Plug the DLC cable from the Hi-Scan Pro into the data link connector (16-pin connector) located to the left of the steering wheel under the instrument panel.
4. Turn the ignition to the ON position.
5. Turn the Hi-Scan Pro ON and press ENTER.
6. Select option "52. LC 1.5S/1.6D 00-04MY 02 SENSOR." and press ENTER.
7. Select option "01. 1.5S/1.6D 00-04MY 02 SENSOR [AUTO]" and press ENTER.
This option automatically detects the ECM type and downloads the correct program.
8. Enter "1229" as the password for the automatic update mode and press ENTER.
9. The Hi-Scan Pro will establish communication and check the ECM ID. The Hi-Scan Pro will reprogram the ECM automatically.
NOTE:
^ The Hi-Scan Pro detects the current ECM ID, assigns the new ECM ID and displays them for a short time.
^ To be prepared in case a reprogramming error occurs, write down the "NEW ECM ID" displayed on the Hi-Scan Pro screen during reprogramming.
^ It will be used during the Manual Update Procedure if the program does not download correctly.
^ If the Hi-Scan Pro does not download the program, use the Manual Update Procedure following this section.
^ Check the ECM IDs displayed on the Hi-Scan Pro screen to verify that the correct ECM software is being downloaded. Refer to the "ECM SPECIFICATION TABLE" shown previously in this bulletin for the ECM ID listing.
WARNING:
Do not interrupt the reprogramming at any time. The ECM will be rendered inoperative if the program does not download completely.
10. When the COMPLETED message is displayed, turn the Hi-Scan Pro OFF and the process is complete.
NOTE:
When reprogramming has been completed successfully, turn the ignition to the OFF position for 20 seconds and then start the engine to check for proper operation.
MANUAL UPDATE PROCEDURE:
NOTE:
In the event menu option "01. 1.5S/1.6D 00-04MY 02 SENSOR [AUTO]" fails to download the new ECM program, option "02. 1.5S/1.6D 00-04MY 02 SENSOR [ERROR]" must be used.
1. Turn the ignition to the ON position.
2. Turn the Hi-Scan Pro ON and press ENTER.
3. Select menu option "" and press ENTER.
4. Select menu option "02. 1.5S/1.6D 00-04MY 02 SENSOR [ERROR]" for manual update and press ENTER.
5. Choose the correct specification for your vehicle by identifying the VIN and engine and by referring to the "ECM SPECIFICATION TABLE" shown previously in this bulletin to choose one of 10 choices. Then press ENTER.
NOTE:
If the vehicle is equipped with ECM P/N 39110-22550, use option 01. for 39110-22551.
NOTE:
If the vehicle is equipped with ECM P/N 39110-22560, use option 02. for 39110-22561.
6. Select the correct password for Manual Update from the "ECM SPECIFICATION TABLE shown previously in this bulletin.
^ Enter the correct password and press ENTER.
WARNING:
If an incorrect password is used, the correct ECM software will not be downloaded.
7. Wait until the reprogramming is completed. The Hi-Scan Pro will reprogram the ECM.
NOTE:
Once the password is entered and accepted, the rest of the procedure is exactly the same as the automatic update procedure.
8. Compare the new ECM ID displayed on the Hi-Scan Pro screen with the one that's listed as the correct new ECM ID in the table shown previously in this TSB, to make sure that the correct software has been installed.
9. When the COMPLETED message is displayed, turn the Hi-Scan Pro OFF and the process is complete.
NOTE:
When reprogramming has been completed successfully, turn the ignition to the OFF position for 20 seconds and then start the engine to check for proper operation.
EXPLANATION OF ERROR MESSAGE:
1. "INVALID PASSWORD": Please enter the correct password again.
2. "REPROGRAMMING ERROR PLEASE WAIT FOR RETRY": An error occurred during reprogramming, the Hi-Scan Pro will retry the reprogramming automatically.
3. "ALREADY REPROGRAMMED" or "INCORRECT TARGET ID": The reprogramming has previously been done on this vehicle or the ECM is not the type subject for this reprogramming procedure.
4. "REPROGRAM ERROR PLEASE CHECK THE SYSTEM": In this case you must reprogram manually after selecting the menu option "02. 1.5S/1.6D 00-04MY 02 SENSOR [ERROR]".