DTC 063

DTC 063

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.

DTC Descriptor
DTC 063
- PPS Out of Calibration

Circuit/System Description

The Inflatable Restraint Passenger Presence System (PPS) is used to monitor the weight of an occupant on the front outboard passenger seat and communicate the status to the sensing and diagnostic module (SDM) whether to enable or suppress the deployment of the instrument panel (I/P) module. The PPS consist of an electronic control module, silicone filled sensor pad, pressure sensor, seat belt tension retractor sensor, wiring harness, and PASSENGER AIR BAG ON/OFF indicators. The silicone filled sensor pad is located under the passenger seat foam cushion and is connected by a hose clamped to the pressure sensor. The weight of the occupant sitting in the front passenger seat is measured as a pressure change within the bladder by the pressure sensor. The pressure sensor sends a voltage signal to the PPS module. If the pressure from the occupant's weight is less than a specified value, the PPS module will send a suppress signal to the SDM to disable the I/P module. If the pressure from the occupant's weight is higher than a specified value, the PPS module will send an enable signal to the SDM to enable the I/P module. The PPS module will notify the customer of the enable/disable status by illuminating one of the PASSENGER AIR BAG ON/OFF indicators located on the instrument panel. The PPS monitors itself for faults and will set flash DTCs if a fault is detected. The PPS will also notify the SDM of a fault. The SDM will respond by setting DTC B0092 and requesting the instrument panel cluster (IPC) to illuminate the AIR BAG indicator. The PPS will set DTC 063 as an indication that the PPS is out of calibration. The PPS is not capable of being calibrated at the service level, the PPS must be replaced.

Conditions for Running the DTC

Ignition voltage is between 9-16 volts.

Conditions for Setting the DTC

The PPS detects ignition 1 voltage is less than 8 volts for 500 milliseconds.

Action Taken When the DTC Sets

* The PPS will set a DTC, and then communicate with the SDM.
* The SDM will set DTC B0081.
* The SDM disables the instrument panel (I/P) module deployment loop.
* The PPS will illuminate the passenger air bag status OFF indicator.
* The SDM requests the instrument panel cluster (IPC) to illuminate the AIR BAG indicator.

Conditions for Clearing the DTC

DTC 063 is an indication that the PPS is out of calibration. You cannot recalibrate the PPS. Replace the PPS after following the instructions in the diagnostic table below.

Diagnostic Aids

The presence of current or history DTCs while attempting to rezero the PPS will cause the PPS module to set DTC 063. Verify that all SIR and PPS DTCs have been cleared before rezeroing the PPS.

Reference Information
Schematic Reference

SIR Schematics ([1][2]Air Bag Systems)
Connector End View Reference

Component Connector End Views (Connector End Views By Name)
Description and Operation

SIR System Description and Operation (Description and Operation)
Electrical Information Reference

* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)

Scan Tool Reference

Control Module References (Programming and Relearning) for scan tool information

Circuit/System Verification

Ignition ON, clear all SIR and PPS DTCs. Refer to Passenger Presence System Flash Code Procedures (Component Tests and General Diagnostics). Rezero the PPS using the Control Module References (Programming and Relearning). Verify DTC 063 does not reset.

If DTC 063 resets, replace the PPS module.

Repair Instructions

Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.

* SIR/SRS Wiring Repairs (Component Tests and General Diagnostics)
* Control Module References (Programming and Relearning) for PPS replacement, setup, and programming