C0131
DTC C0131
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC C0131
- Antilock Brake System (ABS) Pressure Circuit
Circuit/System Description
The ABS pump motor and accumulator operates the ABS and base brake power assist systems. Pressurized brake fluid is stored in the accumulator and used for ABS and base brake power assist functions. An accumulator pressure sensor located internally in the electronic brake control module (EBCM) monitors the accumulator pressure. If accumulator pressure becomes too low, the ABS pump motor is commanded ON.
Conditions for Running the DTC
Ignition ON.
Conditions for Setting the DTC
* The accumulator internal power supply is out of range.
* The accumulator pressure sensor value changes more than 15 MPa in 0.08 seconds.
* The accumulator pressure signal fails to change at least 0.12 MPa during the accumulator pressure test.
* The EBCM detects that the accumulator pressure signal is too low when the vehicle is driven.
Action Taken When the DTC Sets
* The EBCM disables the Antilock Brake System (ABS)/Traction Control System (TCS)/Vehicle Stability Enhancement System (VSES) for the duration of the ignition cycle.
* A DIC message and/or a warning indicator may be displayed.
Conditions for Clearing the DTC
* The condition for the DTC is no longer present.
* The EBCM clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles.
Diagnostic Aids
The accumulator pressure sensor is located internally in the BPMV and is not serviceable.
Reference Information
Schematic Reference
Antilock Brake System Schematics (Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
ABS Description and Operation (Description and Operation)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information.
Circuit/System Verification
Important: It is recommend that the defective components be replaced, and not the complete brake master cylinder assembly.
1. Verify that DTCs C0110 or C0201 are not set.
• If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (Diagnostic Trouble Code Descriptions).
2. Cycle the ignition from OFF to ON. Observe the accumulator pressure data parameter on the scan tool. Fully apply and release the brake pedal once, the accumulator pressure should hold steady above 16.7 MPa.
• If the accumulator pressure data parameter does not hold steady above 16.7 MPa, replace the accumulator.
3. Wait 60 seconds without depressing the pedal. The pump motor should not turn on.
• If the ABS pump motor turns ON and OFF several times, replace the EBCM/brake pressure modulator valve (BPMV) assembly.
4. Cycle the ignition from OFF to ON. Apply and release the brake pedal continuously. The accumulator pressure should not be below 14.9 MPa for 100 seconds consecutively.
• If the accumulator pressure stays below 14.9 MPa for 100 seconds, replace the EBCM/BPMV assembly.
5. Test drive the vehicle and observe the accumulator pressure data parameter while driving. The accumulator should not fluctuate rapidly.
• If the accumulator pressure fluctuates rapidly replace the EBCM/BPMV assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Electronic Brake Control Module with Brake Pressure Modulator Valve Replacement (Electronic Brake Control Module with Brake Pressure Modulator Valve Replacement)
* Power Brake Booster Pump Fluid Accumulator Replacement (without RPO BRM) (Power Brake Booster Pump Fluid Accumulator Replacement (without RPO BRM))Power Brake Booster Pump Fluid Accumulator Replacement (with RPO BRM) (Power Brake Booster Pump Fluid Accumulator Replacement (with RPO BRM))
* Control Module References (Programming and Relearning) for EBCM and BPMV replacement, setup, and programming