Front Windows - Bind or Out of Run Channel
97-021March 28, 2000
Applies To:
1996-00 Civic 2-door - - See VEHICLES AFFECTED
Front Windows Bind or Have Come Out of the Run Channel
(Supersedes 97-021, dated February 22, 2000)
SYMPTOM
One or both of the front windows are binding or have come out of the window run channel.
PROBABLE CAUSE
1996 and 1997 models thru the affected VINS:
Faulty window regulator, and the glass run channel is not seated correctly in the window channels.
1997 models after the affected VINs, all 1998-99 models, and 2000 models thru the affected VINs:
The glass run channel is not seated correctly in the window channels.
VEHICLES AFFECTED
Replace the window regulator(s), and reinstall the glass run channel on the vehicles shown.
Reinstall the glass run channel on the vehicles shown.
CORRECTIVE ACTION
1996 and 1997 models thru the affected VINs:
Replace the window regulator, and reinstall the glass run channel. Replace the glass run channel if it is damaged.
1997 models after the affected VINs, all 1998-99 models, and 2000 models thru the affected VINs:
Reinstall the glass run channel. Replace the glass run channel if it is damaged.
WARRANTY CLAIM INFORMATION
In warranty: The normal warranty applies.
Failed Part: Left P/N 04725-S00-A00
H/C 4835880
Right P/N 04720-S00-A00
H/C 4835864
Defect Code: 030
Contention Code: B99
Skill Level: Repair Technician
Out of warranty: Any repair performed after warranty expiration may be eligible for goodwill consideration by the District Service Manager or your Zone Office. You must request consideration, and get a decision, before starting work.
PARTS INFORMATION
Left Power Window Regulator:
P/N 04725-S00-A01, H/C 5254545
Left Manual Window Regulator:
P/N 72250-S00-003, H/C 4847117
Left Glass Run Channel:
P/N 72275-S03-G01, H/C 4847166
Right Power Window Regulator:
P/N 04720-S00-A01, H/C 5254537
Right Manual Window Regulator:
P/N 72210-S00-003, H/C 4847026
Right Glass Run Channel:
P/N 72235-S03-G01, H/C 4847083
REQUIRED MATERIALS
Plastic Cover Adhesive:
P/N 08712-0003, H/C 4162186
REPAIR PROCEDURE
1. Remove the door panel. Refer to section 20 of the 1996-00 Civic Service Manual.
2. Remove the armrest bracket, then pull down the plastic cover to gain access to the window regulator.
3. Carefully move the glass until you can see the glass mounting bolts, then loosen them. Slide the guide rearward, remove the glass from the guide, and carefully pull the glass out through the window slot.
4. Check the year and VIN.
^ If the vehicle is a 1996 or 1997 within the affected VIN range, replace the window regulator. Go to step 5.
^ If the vehicle is not a 1996 or 1997 within the affected VIN range, go to step 8.
5. Remove the two roller guide bolts and the two rear regulator mounting bolts; then remove the front regulator mounting bolts.
6. Disconnect the power window motor connector, and detach the harness clip (it applicable); then lift and remove the regulator through the opening in the door.
7. Install the new regulator in the door, then loosely install the two rear mounting bolts and the two roller guide bolts. Do not tighten the two front mounting bolts yet. Go to step 9.
8. Loosen the window regulator's two rear mounting bolts, two front mounting bolts, and two roller guide bolts.
9. Inspect the glass run channel:
^ If the run channel is not sitting in the window channels properly, reinstall it.
^ If the run channel is damaged, replace it. Refer to section 20 of the appropriate service manual.
^ If the run channel is sitting in the window channels properly, go to step 10.
NOTE: If the run channel is sitting in the window channels properly and the window regulator was not replaced, disregard this service bulletin and follow normal troubleshooting procedures.
10. Reinstall the glass in the door, but do not tighten the glass mounting bolts. Reconnect the power window motor connector, and temporarily reconnect the window switch (if applicable). Raise the window about 100 mm (4.0 in.) from the fully lowered position.
11. Push the glass toward the rear of the door, and have an assistant tighten the two glass mounting bolts, the four regulator mounting bolts, and the two roller guide bolts.
12. Loosen the front channel mounting bolt and nut. Push the front channel toward the glass, and tighten the mounting bolt and nut.
13. Check the window for smooth operation, and check for gaps between the glass and the run channel with the window all the way up.
^ If the window does not operate smoothly, or if you see gaps between the run channel and the window, loosen all the mounting bolts, and repeat steps 10 through 12.
^ If the window operates smoothly and you see no gaps between the run channel and the window, reinstall the plastic cover, the armrest bracket, and the door panel.
Disclaimer