Pinpoint Test K: The Keyless Entry Keypad Illumination Is Inoperative/Does Not Operate Correctly
Handles, Locks, Latches and Entry Systems
Pinpoint Test K: The Keyless Entry Keypad Illumination Is Inoperative/Does Not Operate Correctly
Refer to Wiring Diagram Set 117, Remote Keyless Entry and Alarm for schematic and connector information. [1][2]Diagrams By Number
Normal Operation
When any keypad button is pressed the Smart Junction Box (SJB) sends voltage to the keyless entry keypad LEDs on the illumination circuit to assist the driver in entering an access code at night. The keyless entry keypad has a separate ground circuit for the LEDs.
- DTC B1624 (Lamp Keypad Output Open Circuit)- a continuous and on-demand DTC that sets when the SJB (Smart Junction Box) detects the keyless entry keypad illumination output or ground circuit is open, or the illumination output circuit is shorted to voltage.
- DTC B1626 (Lamp Keypad Output Short Circuit To Ground)- an on-demand DTC that sets when the SJB (Smart Junction Box) detects the keyless entry keypad illumination output circuit is shorted to ground.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- Keyless entry keypad
- SJB (Smart Junction Box)
PINPOINT TEST K : THE KEYLESS ENTRY KEYPAD ILLUMINATION IS INOPERATIVE/DOES NOT OPERATE CORRECTLY
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
NOTE: Failure to disconnect the battery when instructed will result in false resistance readings.
K1 CHECK THE KEYLESS ENTRY KEYPAD OPERATION
- Press the 7/8 and 9/0 buttons simultaneously on the keyless entry keypad.
Do all of the doors lock?
Yes
GO to K2.
No
GO to Pinpoint Test J. Pinpoint Test J: The Doors Do Not Lock/Unlock Using The Keyless Entry Keypad
K2 CHECK THE RECORDED SJB (Smart Junction Box) DTCs FROM THE SELF-TEST
- Check the recorded results from the SJB (Smart Junction Box) self-test.
Is DTC B1626 present?
Yes
GO to K3.
No
GO to K5.
K3 CHECK THE KEYLESS ENTRY KEYPAD FOR A SHORT TO GROUND
- Disconnect: Keyless Entry Keypad C530.
- Clear the DTCs, then repeat the SJB (Smart Junction Box) self-test.
Is DTC B1626 recorded?
Yes
GO to K4.
No
INSTALL a new keyless entry keypad. REFER to Keyless Entry Keypad . TEST the system for normal operation.
K4 CHECK THE KEYPAD ILLUMINATION OUTPUT CIRCUIT FOR A SHORT TO GROUND
- Ignition OFF.
- Disconnect: SJB (Smart Junction Box) C2280C.
- Measure the resistance between the keyless entry keypad C530-6, circuit CPK28 (WH/GN), harness side and ground.
Is the resistance greater than 10,000 ohms?
Yes
GO to K11.
No
REPAIR circuit CPK28 (WH/GN) for a short to ground. CLEAR the DTCs. REPEAT the self-test.
K5 CHECK THE KEYLESS ENTRY KEYPAD ILLUMINATION
- Ignition OFF.
- Check the keyless entry keypad illumination.
Is the keyless entry keypad illumination always on?
Yes
GO to K6.
No
GO to K7.
K6 CHECK THE KEYPAD ILLUMINATION OUTPUT CIRCUIT FOR A SHORT TO VOLTAGE
- Disconnect: SJB (Smart Junction Box) C2280C.
- Ignition ON.
- Observe the keypad illumination.
Is the keypad still illuminated?
Yes
REPAIR circuit CPK28 (WH/GN) for a short to voltage. TEST the system for normal operation.
No
GO to K11.
K7 CHECK THE KEYPAD ILLUMINATION OUTPUT CIRCUIT FOR REFERENCE VOLTAGE
NOTE: The SJB (Smart Junction Box) sends out a constant reference voltage on circuit CPK28 (WH/GN) for its own circuit diagnostics. This voltage is 10 volts +/- 1 volt.
- Disconnect: Keyless Entry Keypad C530.
- Measure the voltage between the keyless entry keypad C530-6, circuit CPK28 (WH/GN), harness side and ground.
Are 10 volts (+/- 1 volt) present?
Yes
GO to K9.
No
GO to K8.
K8 CHECK THE KEYPAD ILLUMINATION OUTPUT CIRCUIT FOR AN OPEN
- Disconnect: SJB (Smart Junction Box) C2280C.
- Measure the resistance between the keyless entry keypad C530-6, circuit CPK28 (WH/GN), harness side and the SJB (Smart Junction Box) C2280C-11, circuit CPK28 (WH/GN), harness side.
Is the resistance less than 5 ohms?
Yes
GO to K11.
No
REPAIR circuit CPK28 (WH/GN) for an open. TEST the system for normal operation.
K9 CHECK FOR SJB (Smart Junction Box) OUTPUT
- Measure the voltage between the keyless entry keypad C530-6, circuit CPK28 (WH/GN), harness side and ground while active commanding the SJB (Smart Junction Box) PID (KY_PAD_LMP) ON.
Is the voltage greater than 11 volts?
Yes
GO to K10.
No
GO to K11.
K10 CHECK THE KEYPAD ILLUMINATION GROUND CIRCUIT FOR AN OPEN
- Disconnect: Negative Battery Cable.
- Measure the resistance between the keyless entry keypad C530-3, circuit GD126 (BK/WH), harness side and ground.
Is the resistance less than 5 ohms?
Yes
INSTALL a new keyless entry keypad. REFER to Keyless Entry Keypad . TEST the system for normal operation.
No
REPAIR the circuit. CLEAR the DTCs. REPEAT the self-test.
K11 CHECK FOR CORRECT SJB (Smart Junction Box) OPERATION
- Disconnect all the SJB (Smart Junction Box) connectors.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect all the SJB (Smart Junction Box) connectors and make sure they seat correctly.
- Operate the system and verify the concern is still present.
Is the concern still present?
Yes
INSTALL a new SJB (Smart Junction Box). TEST the system for normal operation.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.