Autolock and Auto-Unlock Programming

Autolock and Auto-Unlock Programming

Programming the Autolock Feature Using the Door Lock Control Switch

NOTE: The autolock feature can be activated or deactivated independently of the auto-unlock feature.

NOTE: The autolock feature of the Smart Junction Box (SJB) can also be configured ON or OFF with the scan tool. For additional information on module configuration, refer to Information Bus.

NOTE: When programming the autolock feature using the door lock control switch method, the following steps must be carried out within 30 seconds or the procedure will need to be repeated. If the procedure needs to be repeated, wait 30 seconds between programming sessions.

1. NOTE: Prior to beginning, make sure the ignition is in the OFF mode and all vehicle doors are closed.

Switch the ignition from the OFF to the RUN mode.

2. Press the unlock button on the door lock control switch 3 times.

3. Switch the ignition from the RUN to the OFF mode.

4. Press the unlock button on the door lock control switch 3 times.

5. Switch the ignition to the RUN mode. The horn chirps once to indicate that programming mode is entered.

6. To enable/disable the autolock feature, press the unlock button on the door lock control switch, then the lock button. The horn chirps once if the autolocks are disabled or twice (one short chirp followed by a honk) if the autolocks are enabled.

7. Switch the ignition to the OFF mode. The horn chirps once to signal that the programming is complete.

Programming the Autolock Feature Using the Keyless Entry Keypad

NOTE: The autolock feature can be activated or deactivated independently of the auto-unlock feature.

NOTE: The autolock feature of the SJB can also be configured ON or OFF with the scan tool. For additional information on module configuration, refer to Information Bus.

1. Switch the ignition to the OFF mode and close all vehicle doors.

2. Enter the factory set 5-digit keyless entry keypad code.

3. Touch and hold the 3/4 button on the keypad. While holding the 3/4 button, touch the 7/8 button.

4. Release the 7/8 button, then release the 3/4 button. The horn chirps once if the autolocks are disabled or twice (one short chirp followed by a honk) if the autolocks are enabled.

Programming the Autolock Feature Using the Instrument Cluster Message Center

NOTE: The autolock feature can be activated or deactivated independently of the auto-unlock feature.

NOTE: The autolock feature of the SJB can also be configured ON or OFF with the scan tool. For additional information on module configuration, refer to Information Bus.

1. With all the vehicle doors closed, switch the ignition from the OFF to the RUN mode.

2. Press the SETUP button on the message center switch until AUTOLOCK OFF is displayed.

3. Press the RESET button to select ON or OFF. If the autolocks are enabled, the message center will have brackets around the display. If the autolocks are disabled, the message center will have brackets around the display.

Programming the Auto-Unlock Feature Using the Door Lock Control Switch

NOTE: The auto-unlock feature can be activated or deactivated independently of the autolock feature.

NOTE: The auto-unlock feature of the SJB can also be configured ON or OFF with the scan tool. For additional information on module configuration, refer to Information Bus.

NOTE: When programming the auto-unlock feature using the door lock control switch method, the following steps must be carried out within 30 seconds or the procedure will need to be repeated. If the procedure needs to be repeated, wait 30 seconds between programming sessions.

1. NOTE: Prior to beginning, make sure the ignition is in the OFF mode and all vehicle doors are closed.

Switch the ignition from the OFF to the RUN mode.

2. Press the unlock button on the door lock control switch 3 times.

3. Switch the ignition from the RUN to the OFF mode.

4. Press the unlock button on the door lock control switch 3 times.

5. Switch the ignition to the RUN mode. The horn chirps once to indicate that programming mode is entered.

6. To enable/disable the auto-unlock feature, press the lock button on the door lock control switch then the unlock button. The horn chirps once if auto-unlock is disabled or twice (one short chirp followed by a honk) if auto-unlock is enabled.

7. Switch the ignition to the OFF mode. The horn chirps once to signal that the programming is complete.

Programming the Auto-Unlock Feature Using the Keyless Entry Keypad

NOTE: The auto-unlock feature can be activated or deactivated independently of the autolock feature.

NOTE: The auto-unlock feature of the SJB can also be configured ON or OFF with the scan tool. For additional information on module configuration, refer to Information Bus.

1. Switch the ignition to the OFF mode and close all vehicle doors.

2. Enter the factory set 5-digit keyless entry keypad code.

3. Touch and hold the 3/4 button on the keypad. While holding the 3/4 button, touch and release the 7/8 button. While still holding the 3/4 button, touch and release the 7/8 button a second time.

4. Release the 3/4 button. The horn chirps once if auto-unlock is disabled or twice (one short chirp followed by a honk) if auto-unlock is enabled.

Programming the Auto-Unlock Feature Using the Instrument Cluster Message Center

NOTE: The auto-unlock feature can be activated or deactivated independently of the autolock feature.

NOTE: The auto-unlock feature of the SJB can also be configured ON or OFF with the scan tool. For additional information on module configuration, refer to Information Bus.

1. Switch the ignition from the OFF to the RUN mode.

2. Press the SETUP button on the message center switch until AUTOUNLOCK OFF is displayed.

3. Press the RESET button to select ON or OFF. If auto-unlock is enabled, the message center will have brackets around the display. If auto-unlock is disabled, the message center will have brackets around the display.