Pinpoint Test C: The Door Locks Operate Only One Way
Handles, Locks, Latches and Entry Systems
Pinpoint Tests
Pinpoint Test C: The Door Locks Operate Only One Way
Refer to Wiring Diagram Set 110, Power Door Locks for schematic and connector information. Diagrams By Number
Normal Operation
The Smart Junction Box (SJB) sends voltage signals to both door lock control switches through the lock and unlock input circuits. When the lock or unlock switch is pressed, the corresponding voltage signal is routed to ground, signalling the SJB to lock or unlock the doors. The door lock control switches have a dedicated ground circuit.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- Door lock control switch
- SJB
PINPOINT TEST C: THE DOOR LOCKS OPERATE ONLY ONE WAY
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
-------------------------------------------------
C1 CHECK THE RECORDED SJB DTCs FROM THE ON-DEMAND SELF-TEST
- Check the recorded results from the SJB self-test.
- Is DTC B2A25 present?
Yes
GO to Pinpoint Test E. Pinpoint Test E: DTC B2A25
No
GO to C2.
-------------------------------------------------
C2 VERIFY THE OPERATION OF BOTH DOOR LOCK CONTROL SWITCHES
- Ignition OFF.
- Press the lock and unlock button of both door lock control switches while observing the door lock operation.
- Do the door locks operate only one way from both switches?
Yes
GO to C4.
No
GO to C3.
-------------------------------------------------
C3 CHECK THE LOCK INPUT OR UNLOCK INPUT CIRCUIT FOR AN OPEN (SINGLE SWITCH INOPERATIVE)
- Disconnect: Suspect Door Lock Control Switch .
- Lock the doors from the working door lock control switch.
- Observe the door locks while connecting a fused jumper wire between the driver door lock control switch C505-2, circuit CPK23 (YE/VT), harness side and the driver door lock control switch C505-1, circuit GD133 (BK), harness side; or between the passenger door lock control switch C605-2, circuit CPK23 (YE/VT), harness side and the passenger door lock control switch C605-1, circuit GD139 (BK/YE), harness side.
- Remove the jumper wire.
- Observe the door locks while connecting a fused jumper wire between the driver door lock control switch C505-4, circuit CPK19 (BU/GN), harness side and the driver door lock control switch C505-1, circuit GD133 (BK), harness side; or between the passenger door lock control switch C605-4, circuit CPK19 (BU/GN), harness side and the passenger door lock control switch C605-1, circuit GD139 (BK/YE), harness side.
- Do the doors lock and unlock with the jumper wire connected?
Yes
INSTALL a new door lock control switch. REFER to Door Lock Control Switch Service and Repair. TEST the system for normal operation.
No
REPAIR the input circuit in question for an open. TEST the system for normal operation.
-------------------------------------------------
C4 CHECK THE LOCK INPUT OR THE UNLOCK INPUT CIRCUIT FOR AN OPEN (BOTH SWITCHES INOPERATIVE)
- Disconnect: Driver Door Lock Control Switch C505 .
- Disconnect: SJB C2280c .
- If the doors do not lock, measure the resistance between the SJB C2280c-17, circuit CPK19 (BU/GN), harness side and the driver door lock control switch C505-4, circuit CPK19 (BU/GN), harness side.
- If the doors do not unlock, measure the resistance between the SJB C2280c-4, circuit CPK23 (YE/VT), harness side and the driver door lock control switch C505-2, circuit CPK23 (YE/VT), harness side.
- Is the resistance less than 5 ohms?
Yes
GO to C5.
No
REPAIR the circuit in question for an open. TEST the system for normal operation.
-------------------------------------------------
C5 CHECK FOR CORRECT SJB OPERATION
- Disconnect all the SJB connectors.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect all the SJB connectors and make sure they seat correctly.
- Operate the system and verify the concern is still present.
- Is the concern still present?
Yes
INSTALL a new SJB. REFER to Body Control Systems. TEST the system for normal operation.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
-------------------------------------------------