Pinpoint Test J: Intermittent No High Speed Controller Area Network (HS-CAN) Communication, Communication Can Be Intermittently
Communications Network
Pinpoint Tests
Pinpoint Test J: Intermittent No High Speed Controller Area Network (HS-CAN) Communication, Communication Can Be Intermittently Established
Normal Operation
The High Speed Controller Area Network (HS-CAN) is used for communication between the PCM, the ABS module and the Instrument Cluster (IC). An open circuit VDB04 (WH/BU) (HS-CAN +) or VDB05 (WH) (HS-CAN -) may cause intermittent or unreliable communication to all modules on the HS-CAN.
In the event that either circuit VDB04 (WH/BU) (HS-CAN +) or VDB05 (WH) (HS-CAN -) becomes open to any module on the network, unreliable network communication to all modules on the network may result.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
PINPOINT TEST J: INTERMITTENT NO HS-CAN COMMUNICATION, COMMUNICATION CAN BE INTERMITTENTLY ESTABLISHED
NOTE: Various modules will set network DTCs during this test procedure. Clear DTCs from all modules after the diagnostic procedure is completed.
NOTE: Failure to disconnect the battery when instructed will result in false resistance readings. Refer to Battery.
-------------------------------------------------
J1 CHECK THE DLC PINS FOR DAMAGE
- Ignition OFF.
- Disconnect the scan tool cable from the Data Link Connector (DLC).
- Inspect DLC pins 6 and 14 for damage.
- Are DLC pins 6 and 14 OK?
Yes
GO to J2.
No
REPAIR the DLC as necessary. CLEAR the DTCs. REPEAT the network test with the scan tool.
-------------------------------------------------
J2 CHECK THE HS-CAN TERMINATION RESISTANCE
- Disconnect: Negative Battery Cable.
- Measure the resistance between the DLC C251-6, circuit VDB04 (WH/BU), harness side and the DLC C251-14, circuit VDB05 (WH), harness side.
- Is the resistance between 54 and 66 ohms?
Yes
GO to J3.
No
Go To Pinpoint Test K. Pinpoint Test K: No High Speed Controller Area Network (HS-CAN) Communication, All Modules Are Not Responding
-------------------------------------------------
J3 CHECK THE HS-CAN (+) AND HS-CAN (-) CIRCUITS FOR A SHORT TO GROUND
- Measure the resistance between the DLC C251-6, circuit VDB04 (WH/BU), harness side and ground; and between the DLC C251-14, circuit VDB05 (WH), harness side and ground.
- Are the resistances greater than 1,000 ohms?
Yes
CONNECT the negative battery cable. GO to J4.
No
Go To Pinpoint Test K. Pinpoint Test K: No High Speed Controller Area Network (HS-CAN) Communication, All Modules Are Not Responding
-------------------------------------------------
J4 CHECK THE HS-CAN (+) AND HS-CAN (-) CIRCUITS FOR A SHORT TO VOLTAGE
- Ignition ON.
- Measure the voltage between the DLC C251-6, circuit VDB04 (WH/BU), harness side and ground; and between the DLC C251-14, circuit VDB05 (WH), harness side and ground.
- Is the voltage greater than 6 volts?
Yes
REPAIR the circuit. CLEAR the DTCs. REPEAT the network test with the scan tool.
No
GO to J5.
-------------------------------------------------
J5 CHECK FOR RESTORED COMMUNICATION WITH THE PCM DISABLED
NOTE: An IDS session must be established prior to disabling the PCM in this test step. If the PCM has failed communication during multiple attempts to identify the vehicle, first identify the vehicle manually by entering a PCM part number, calibration number or tear tag when prompted by IDS.
NOTE: When a vehicle is manually identified by a PCM part number, calibration number or tear tag, the IDS will not automatically run a network test. The network test must be manually selected and run.
NOTE: When re-running the network test, the network test application must be first closed or the screen display will revert back to the prior run network test results.
- Disconnect: Bussed Electrical Center (BEC) Fuses 42 (15A), 45 (10A) and SJB fuse 19 (5A).
- Enter the following diagnostic mode on the scan tool: Network Test.
- Repeat the network test.
- Do all other modules pass the network test?
Yes
INSTALL the removed fuses. Go To Pinpoint Test A. Pinpoint Test A: The PCM Does Not Respond To The Scan Tool
No
INSTALL the removed fuses. GO to J6.
-------------------------------------------------
J6 CHECK FOR RESTORED NETWORK COMMUNICATION WITH THE ABS MODULE DISABLED
NOTE: When re-running the network test, the network test application must be first closed or the screen display will revert back to the prior run network test results.
- Disconnect: BEC Fuse 65 (30A) and SJB fuse 18 (10A).
- Enter the following diagnostic mode on the scan tool: Network Test.
- Repeat the network test.
- Do all other modules pass the network test?
Yes
INSTALL the removed fuse. Go To Pinpoint Test B. Pinpoint Test B: The ABS Module Does Not Respond To The Scan Tool
No
INSTALL the removed fuse. GO to J7.
-------------------------------------------------
J7 CHECK FOR RESTORED NETWORK COMMUNICATION WITH THE IC DISABLED
NOTE: When re-running the network test, the network test application must be first closed or the screen display will revert back to the prior run network test results.
- Disconnect: SJB Fuses 16 (5A) and 19 (5A).
- Enter the following diagnostic mode on the scan tool: Network Test.
- Repeat the network test.
- Do all other modules pass the network test?
Yes
INSTALL the removed fuses. Go To Pinpoint Test C. Pinpoint Test C: The Instrument Cluster (IC) Does Not Respond To The Scan Tool
No
INSTALL the removed fuses. GO to J8.
-------------------------------------------------
J8 CHECK FOR RESTORED NETWORK COMMUNICATION WITH THE IC DISCONNECTED
- Disconnect: IC C220.
- Enter the following diagnostic mode on the scan tool: Network Test.
- Repeat the network test.
- Do all other modules pass the network test?
Yes
CONNECT the IC. Go To Pinpoint Test C. Pinpoint Test C: The Instrument Cluster (IC) Does Not Respond To The Scan Tool
No
CONNECT the IC. An intermittent fault is not present. Go To Pinpoint Test K. Pinpoint Test K: No High Speed Controller Area Network (HS-CAN) Communication, All Modules Are Not Responding
-------------------------------------------------