Pinpoint Test A: The PCM Does Not Respond To The Scan Tool
Communications Network
Pinpoint Tests
Pinpoint Test A: The PCM Does Not Respond To The Scan Tool
Refer to Wiring Diagram Set 14, Module Communications Network for schematic and connector information. Diagrams By Number
Refer to Wiring Diagram Set 23, Electronic Engine Controls - 4.0L for schematic and connector information. Diagrams By Number
Refer to Wiring Diagram Set 24, Electronic Engine Controls - 4.6L for schematic and connector information. Diagrams By Number
Refer to Wiring Diagram Set 25, Electronic Engine Controls - 5.4L for schematic and connector information. Diagrams By Number
Normal Operation
The PCM communicates with the scan tool through the High Speed Controller Area Network (HS-CAN). Circuits 1827 (WH/LG) (HS-CAN +) and 1828 (PK/LG) (HS-CAN -) provide the network connection to the PCM. The PCM shares the HS-CAN with the ABS module (if equipped), and the Instrument Cluster (IC).
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- PCM
PINPOINT TEST A: THE PCM DOES NOT RESPOND TO THE SCAN TOOL
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
NOTE: Failure to disconnect the battery when instructed will result in false resistance readings. Refer to Battery.
-------------------------------------------------
A1 VERIFY WHETHER OTHER HS-CAN MODULES PASS THE NETWORK TEST
- Enter the following diagnostic mode on the scan tool: Network Test.
- In the left hand pane of the IDS network test display screen, verify whether any HS-CAN modules passed the network test.
- Is the text "pass" or a DTC listed next to any of the following modules: ABS module, Instrument Cluster (IC) or PCM?
Yes
If "pass" or a DTC was listed next to the PCM, a network fault is not currently present. Go To Pinpoint Test J to diagnose an intermittent HS-CAN fault condition. Pinpoint Test J: Intermittent No High Speed Controller Area Network (HS-CAN) Communication, Communication Can Be Intermittently
If "pass" or a DTC was listed next to one or more modules other than the PCM, GO to A2.
No
No modules are currently communicating on the HS-CAN. Go To Pinpoint Test K to diagnose no HS-CAN communication. Pinpoint Test K: No High Speed Controller Area Network (HS-CAN) Communication, All Modules Are Not Responding
-------------------------------------------------
A2 COMPUTERS AND CONTROL SYSTEMS INFORMATION PINPOINT TEST QA VERIFICATION CHECK
- Verify that the Computers and Control Systems Information pinpoint test QA has been performed.
- Has pinpoint test QA been performed?
Yes
GO to A3.
No
REFER to Computers and Control Systems Information, Pinpoint Tests, pinpoint test QA to diagnose no communication with the PCM.
-------------------------------------------------
A3 CHECK THE HS-CAN TERMINATION RESISTANCE
- Ignition OFF.
- Disconnect: Negative Battery Cable.
- Measure the resistance between the Data Link Connector (DLC) C251-6, circuit 1827 (WH/LG), harness side and the DLC C251-14, circuit 1828 (PK/LG), harness side.
- Is the resistance between 54 and 66 ohms?
Yes
CONNECT the negative battery cable. GO to A5.
No
GO to A4.
-------------------------------------------------
A4 CHECK THE CAN CIRCUITS BETWEEN THE PCM AND THE DLC FOR AN OPEN
- Disconnect: PCM C175b.
- Measure the resistance between the PCM C175b-11, circuit 1827 (WH/LG), harness side and the DLC C251-6, circuit 1827 (WH/LG), harness side.
- Measure the resistance between the PCM C175b-23, circuit 1828 (PK/LG), harness side and the DLC C251-14, circuit 1828 (PK/LG), harness side.
- Are the resistances less than 5 ohms?
Yes
CONNECT the negative battery cable. GO to A5.
No
REPAIR the circuit in question. CONNECT the negative battery cable. CLEAR the DTCs. REPEAT the network test with the scan tool.
-------------------------------------------------
A5 CHECK FOR CORRECT PCM OPERATION
- Disconnect all the PCM connectors.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect all the PCM connectors and make sure they seat correctly.
- Operate the system and verify the concern is still present.
- Is the concern still present?
Yes
INSTALL a new PCM. CLEAR the DTCs. REPEAT the network test with the scan tool.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. CLEAR the DTCs. REPEAT the network test with the scan tool.
-------------------------------------------------