Misc. Engine Components
* ALL FASTENERS SHOULD BE CLEAN AND LIGHTLY OILED.| A/C Compressor to Bracket Bolt | 7/16"-14 | 50 Foot Pound-Force (ft.lb) |
| A/C Compressor Support Bolts | 3/8"-16 | 30 Foot Pound-Force (ft.lb) |
| Alternator Adjusting Strap Bolt | 5/16"-18 | 200 Inch Pound-Force (in.lb) |
| Alternator Adjusting Strap Mounting Bolt | 3/8"-16 | 30 Foot Pound-Force (ft.lb) |
| Alternator Bracket Bolt | 3/8"-16 | 30 Foot Pound-Force (ft.lb) |
| Alternator Mounting Pivot Nut | 3/8"-16 | 30 Foot Pound-Force (ft.lb) |
| Camshaft Sprocket Lock Bolt | M10 x 1.5 | 40 Foot Pound-Force (ft.lb) |
| Camshaft Thrust Plate | M6 x 1 | 105 Inch Pound-Force (in.lb) |
| Chain Case Cover Bolt | M8 x 1.25 | 20 Foot Pound-Force (ft.lb) |
| M10 x 1.5 | 40 Foot Pound-Force (ft.lb) | |
| Connecting Rod Nut | 3/8"-24 | 40 Foot Pound-Force (ft.lb) + 1/4 turn (DO NOT USE A TORQUE WRENCH FOR THIS STEP) |
| Crankshaft Pulley Screw to Crankshaft | M10 x 1.5 | 40 Foot Pound-Force (ft.lb) |
| Cylinder Head Bolt | M8 x 1.25 | 25 Foot Pound-Force (ft.lb) |
| M11 x 1.5 (Step 1) | 45 Foot Pound-Force (ft.lb) | |
| M11 x 1.5 (Step 2) | 65 Foot Pound-Force (ft.lb) | |
| M11 x 1.5 (Step 3) | 65 Foot Pound-Force (ft.lb) | |
| M11 x 1.5 (Step 4) | + 1/4 turn DO NOT USE A TORQUE WRENCH FOR THIS STEP. | |
| Cylinder Head Cover Bolts | M6 x 1.0 | 105 Inch Pound-Force (in.lb) |
| Exhaust Manifold Screws | M8 x 1.25 | 200 Inch Pound-Force (in.lb) |
| Exhaust Crossover Pipe Flange Nut/Bolt | M10 x 1.5 | 25 Foot Pound-Force (ft.lb) |
| Intake Manifold Bolt | M8 x 1.25 | 200 Inch Pound-Force (in.lb) |
| Intake Manifold Gasket Retaining Screws | M6 x 1 | 105 Inch Pound-Force (in.lb) |
| Intake Manifold Plenum Bolt | M8 x 1.75 | 250 Inch Pound-Force (in.lb) |
| Main Bearing Cap Bolt | M11 x 1.5 | 30 Foot Pound-Force (ft.lb) + 1/4 turn (DO NOT USE A TORQUE WRENCH FOR THIS STEP) |
| Oil Filter Attaching Nipple | 3/4"-16 | 30 Foot Pound-Force (ft.lb) |
| Oil Level Sensor Plug | 3/4"-16 | 20 Foot Pound-Force (ft.lb) |
| Oil Pan Drain Plug | 1/2"-20 | 20 Foot Pound-Force (ft.lb) |
| Oil Pan Screw | M6 x 1.0 | 105 Inch Pound-Force (in.lb) |
| Oil Pressure Gauge Sending Unit | 1/8" NPTF | 60 Inch Pound-Force (in.lb) |
| Oil Pump Cover Bolt T-30 | M6 x 1.0 x 18 | 105 Inch Pound-Force (in.lb) |
| Oil Pump Pick-up Tube Screw | M8 x 1.75 | 250 Inch Pound-Force (in.lb) |
| PCV Valve | 3/8"-16 NPTF | 60 Inch Pound-Force (in.lb) |
| Rocker Shaft Bracket Bolt | 5/16"-18 | 250 Inch Pound-Force (in.lb) |
| Spark Plug | 14 mm | 20 Foot Pound-Force (ft.lb) |
| Starter Mounting Bolt | 7/16"-14 | 50 Foot Pound-Force (ft.lb) |
| Strut Intake Manifold to Cylinder Head Bolt | M10 x 1.5 | 40 Foot Pound-Force (ft.lb) |
| Tappet Retainer Yoke Screw | M6 x 1 | 105 Inch Pound-Force (in.lb) |
| Temperature Gauge Sending Unit | 1/8" NPTF | 60 Inch Pound-Force (in.lb) |
| Timing Chain Snubber Screw | M6 x 1.0 | 105 Inch Pound-Force (in.lb) |
| Water Pump to Chain Case Cover Bolt | M6 x 1.0 | 105 Inch Pound-Force (in.lb) |