Wipers/Washers - Rear Wiper Inop./DTC's B231B/B2215
NUMBER: 08-027-06GROUP: Electrical
DATE: June 5, 2006
THE StarSCAN(R) FLASH FILES FOR THIS BULLETIN MUST BE RETRIEVED FROM
THE INTERNET.
StarSCAN(R) UPDATE CD 6.05 WAS THE LAST CD TO CONTAIN FLASH FILES.
SUBJECT:
Flash - Rear Wiper Stops Operating with Diagnostic Trouble Codes B231B And B2215
OVERVIEW:
This bulletin involves Flash Reprogramming the Totally Integrated Power Module (11PM) with updated software.
MODELS:
2006 (PT) PT Cruiser
2007 (PM) Caliber
NOTE:
This bulletin applies to PM vehicles built before May 27, 2006 (MDH 0527XX) and all PT vehicles built before June 2, 2006 (MDH 0602XX)
SYMPTOM/CONDITION:
The rear wiper may stop operating. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTC's) are present::
A. B2215 - FCM Internal
B. B231B - Rear Wiper Motor Control Circuit Low
DIAGNOSIS:
1. Connect the StarSCAN(R) to the vehicle.
2. Turn the ignition on.
3. With the Scan Tool, clear all TIPM DTC's.
4. Turn the Rear Windshield Wipers on.
5. Does the rear wiper operate?
6. Yes >> Perform the Repair Procedure.
7. No >> This bulletin does not apply, additional diagnosis is required.
SPECIAL TOOLS / EQUIPMENT REQUIRED:
REPAIR PROCEDURE - USING THE INTERNET TO RETRIEVE THE FLASH FILE:
NOTE:
Before performing this Repair Procedure, the operating software in the StarSCAN(R); must be programmed with software release level 6.06 or higher.
The software release level is visible in the blue header at the top of the StarSCAN(R) screen.
NOTE:
The StarSCAN(R) diagnostic scan tool fully supports Internet connectivity. However, to take advantage of this feature you must first configure the StarSCAN(R) for your dealership's network. Make sure the StarSCAN(R) is configured to the dealership's network before proceeding. For instruction on setting up your StarSCAN(R) for the dealer's network refer to either:
"DealerCONNECT > Service > StarSCAN and StarMOBILE tools > Online Documentation", or refer to the StarSCAN(R) Quick Start Networking Guide. The StarSCAN(R) Quick Start Networking Guide is also available on the website under the "Download Center".
NOTE:
If this flash process is interrupted/aborted, the flash should be restarted.
1. Install a battery charger and verify that the charging rate provides approximately 13.5 volts. Set the battery charger to continuous charge. Do not allow the charger to time out during the flash process. Remove the charger from the battery when the flash process is complete.
2. Connect the CH9410 StarSCAN(R) ethernet cable to the StarSCAN(R) and the dealer's network drop.
3. Connect the CH9404 StarSCAN(R) vehicle cable to the StarSCAN(R) and the vehicle.
4. Power ON the StarSCAN(R).
5. Retrieve the old TIPM part number. Using the StarSCAN(R) at the "Home" screen:
a. Select "ECU View"
b. Touch the screen to highlight the appropriate ECU in the list of modules.
c. Select "More Options"
d. Select "ECU Flash"
e. Record the part number at the top of the "Flash ECU" screen for later reference.
f. Select "Browse for New File". Follow the on screen instructions.
g. Highlight the listed calibration.
h. Select "Download to Scantool".
i. Select "Close" after the download is complete, then select "Back".
j. Highlight the listed calibration.
k. Select "Update Controller". Follow on screen instructions.
l. When the update is complete, select "OK".
m. Verify the part number at the top of the "Flash ECU" screen has updated to the new part number.
NOTE:
Due to the TIPM programming procedure, a DTC may be set in other modules (PCM, TCM, BCM, MIC, SKREEM, etc.) within the vehicle, if so equipped. Some DTC's may cause the MIL to illuminate. From the "Home" screen select "System View". Then select "All DTCs". Press "Clear All Stored DTCs" if there are any DTCs shown on the list.
POLICY:
Reimbursable within the provisions of the warranty.
TIME ALLOWANCE:
FAILURE CODE:
Disclaimer:
This bulletin is supplied as technical information only and is not an authorization for repair.