B185A

B185A-DRIVER WINDOW POSITION SENSOR CIRCUIT PERFORMANCE - DDM





For a complete wiring diagram Consult Diagrams/Electrical.

- When Monitored:
Whenever the module is awake.

- Set Condition:
When one of the window motor hall sensors does not generate a signal during a window movement, this code will set.





Diagnostic Test

1. TEST FOR INTERMITTENT CONDITION
Turn the ignition on.
With the scan tool, record and erase DTC's
Try to operate the Driver Window up and down several times.
Wait 30 seconds.
With the scan tool, read DTC's.
Does the scan tool display B185A-DRIVER WINDOW POSITION SENSOR CIRCUIT PERFORMANCE?

Yes

- Go to 2

No

- The conditions that caused this code to set are not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
- Perform BODY VERIFICATION TEST - VER 1. Body Verification Test

2. (Q301) DRIVER WINDOW HALL SENSOR A SIGNAL SHORT TO GROUND




Turn the ignition off.
Disconnect the Driver Window Motor connector.
Disconnect the Driver Door Module C1 connector.
Measure the resistance between Ground and the (Q301) Driver Window Hall Sensor A Signal circuit.
Is the resistance below 10000.0 ohms?

Yes

- Repair the (Q301) Driver Window Hall Sensor A signal circuit for a short to ground.
- Perform BODY VERIFICATION TEST - VER 1. Body Verification Test

No

- Go to 3

3. (Q303) DRIVER WINDOW HALL SENSOR B SIGNAL CIRCUIT SHORT TO GROUND




Measure the resistance between Ground and the (Q303) Driver Window Hall Sensor B Signal circuit.
Is the resistance below 10000.0 ohms?

Yes

- Repair the (Q303) Driver Window Hall Sensor B Signal circuit for a short to ground.
- Perform BODY VERIFICATION TEST - VER 1. Body Verification Test

No

- Go to 4

4. (Q301) DRIVER WINDOW HALL SENSOR A SIGNAL CIRCUIT OPEN




Measure the resistance of the (Q301) Driver Window Hall Sensor A Signal circuit between the Motor connector (JS41-Cav 6) (JS27-Cav 2) and the Module C1 connector.
Is the resistance below 1.0 ohms?

No

- Repair the (Q301) Driver Window Hall Sensor A Signal circuit for an open.
- Perform BODY VERIFICATION TEST - VER 1. Body Verification Test

Yes

- Go to 5

5. (Q303) DRIVER WINDOW HALL SENSOR B SIGNAL CIRCUIT OPEN




Measure the resistance of the (Q303) Driver Window Hall Sensor B Signal circuit between the Motor connector (JS41-Cav 2) (JS27-Cav 6) and the Module C1 connector.
Is the resistance below 1.0 ohms?

No

- Repair the (Q303) Driver Window Hall Sensor B Signal circuit for an open.
- Perform BODY VERIFICATION TEST - VER 1. Body Verification Test

Yes

- Go to 6

6. (Q303) DRIVER WINDOW HALL SENSOR B SIGNAL CIRCUIT SHORTED TO THE (Q991) DRIVER WINDOW HALL SENSOR RETURN CIRCUIT




Measure the resistance between the (Q303) Driver Window Hall Sensor B Signal circuit (JS41-Cav 2) (JS27-Cav 6) and the (Q991) Driver Window Hall Sensor Return Ground circuit.
Is the resistance below 10000.0 ohms?

No

- Repair the (Q303) Driver Window Hall Sensor B Signal circuit for a short to the (Q991) Driver Window Hall Sensor Return circuit.
- Perform BODY VERIFICATION TEST - VER 1. Body Verification Test

Yes

- Go to 7

7. (Q301) DRIVER WINDOW HALL SENSOR A SIGNAL CIRCUIT SHORTED TO THE (Q991) DRIVER WINDOW HALL SENSOR RETURN CIRCUIT




Measure the resistance between the (Q301) Driver Window Hall Sensor A Signal circuit (JS41-Cav 6) (JS27-Cav 2) and the (Q991) Driver Window Hall Sensor Return circuit.
Is the resistance below 10000.0 ohms?

No

- Repair the (Q301) Driver Window Hall Sensor A Signal circuit for a short to the (Q991) Driver Window Hall Sensor Return circuit.
- Perform BODY VERIFICATION TEST - VER 1. Body Verification Test

Yes

- Go to 8

8. (Q301) DRIVER WINDOW HALL SENSOR A SIGNAL CIRCUIT SHORT TO (Q303) DRIVER WINDOW HALL SENSOR B SIGNAL CIRCUIT




Measure the resistance between the (Q301) Driver Window Hall Sensor A Signal circuit and the (Q303) Driver Window Hall Sensor B Signal circuit.
Is the resistance below 1000.0 ohms?

Yes

- Repair the (Q301) Driver Window Hall Sensor A Signal circuit for a short to the (Q303) Driver Window Hall Sensor B Signal circuit.
- Perform BODY VERIFICATION TEST - VER 1. Body Verification Test

No

- Replace the Window Motor.
- Perform BODY VERIFICATION TEST - VER 1. Body Verification Test