FREE REPAIR MANUALS & LABOR GUIDES 1982-2013 Vehicles
Courtesy of Operation CHARM: Car repair manuals for everyone.
Home >> Chrysler >> 2008 >> Sebring Convertible V6-2.7L Flex Fuel >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> P Code Charts >> P2175 >> NGC

NGC







P2175-LOW AIRFLOW-RESTRICTION DETECTED (SLOW ACCUMULATION)





For a complete wiring diagram Consult Diagrams/Electrical.

- When Monitored:
Ignition on and engine running with no MAP Sensor DTCs.

- Set Condition:
The PCM detects that the calculated MAP value is greater than actual MAP plus an offset value. One trip fault will set within 5 seconds. ETC light will flash.





Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding.Initial Inspection and Diagnostic Overview

Diagnostic Test

1. ACTIVE DTC

NOTE: Diagnose and repair any TP Sensor or MAP Sensor DTCs before continuing.

NOTE: Diagnose and repair any VSS or 5 Volt supply circuit DTCs before continuing.

NOTE: The throttle plate and linkage should be free from binding and carbon build up.

NOTE: Make sure the throttle plate is at the idle position.

Turn the ignition on.
With the scan tool, select View DTCs. Record DTC and Freeze Frame information.
Start the engine and allow it to reach operating temperature.

WARNING: When the engine is operating, do not stand in direct line with the fan. Do not put your hands near the pulleys, belts, or fan. Do not wear loose clothing. Failure to follow these instructions can result in personal injury or death.

NOTE: Attempt to operate the vehicle under conditions similar to which the DTC was set.

NOTE: It may be necessary to test drive the vehicle within the DTC monitoring conditions in order for this DTC to set.

With a scan tool, select View DTCs.
Is the DTC Active at this time?

Yes

- Go to 2

No

- Refer to the *CHECKING FOR AN INTERMITTENT DTC Diagnostic Procedure. Checking For An Intermittent DTC

2. VACUUM LEAK

NOTE: This code is enabled to limit engine operation if a large vacuum leak should occur.

NOTE: A large vacuum leak is the most probable cause of this DTC.

Inspect the intake manifold, power brake booster, and PCV system for any vacuum leaks.
Inspect the throttle plate. If the throttle blade is bent or will not close, the throttle body may need to be replaced.
Inspect the MAP Sensor and Throttle Body for proper installation.
Inspect the engine for any mechanical conditions that can cause improper engine vacuum.
Inspect the air intake system for any restrictions or obstructions.
Were any problems found?

Yes

- Repair as necessary.
- Perform the PCM Verification Test. Powertrain Verification Test

No

- Go to 3

3. MAP SENSOR OPERATION
Start the engine.
With a scan tool, monitor the MAP Sensor voltage.
Snap the throttle.
Does the MAP Sensor voltage vary from below 2.0 volts at idle to above 3.5 volts at wide open throttle?

Yes

- Go to 5

No

- Go to 4

4. MAP SENSOR
Turn the ignition off.
Disconnect the MAP Sensor harness connector.
Disconnect the C1 and C2 PCM harness connectors.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the MAP Sensor and the Powertrain Control Module (PCM).
Look for any chafed, pierced, pinched, or partially broken wires.
Look for broken, bent, pushed out or corroded terminals.
Check each of the MAP Sensor circuits for high resistance or a shorted condition.
Were any problems found?

Yes

- Repair as necessary.
- Perform the PCM Verification Test. Powertrain Verification Test

No

- Replace the MAP Sensor.
- Perform the PCM Verification Test. Powertrain Verification Test

5. THROTTLE FOLLOWER TEST
Turn the ignition on.
With a scan tool, perform the Throttle Follower Test and monitor the TP Sensor 1 and TP Sensor 2 voltages.
Slowly press the throttle pedal down.
The voltage for TP Sensor 1 should start at approximately 0.3 volts and increase to above 4.7 volts.
The voltage for TP Sensor 2 should start at approximately 4.7 volts and decrease to approximately 0.3 volts.
Is the voltage within the range specified for each sensor?

Yes

- Go to 7

No

- Go to 6

6. THROTTLE BODY
Turn the ignition off.
Disconnect the Throttle Body harness connector.
Disconnect the C2 PCM harness connector.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the Throttle Body and the Powertrain Control Module (PCM).
Look for any chafed, pierced, pinched, or partially broken wires.
Look for broken, bent, pushed out or corroded terminals.
Check each of the Throttle Body circuits for high resistance or a shorted condition.
Were any problems found?

Yes

- Repair as necessary.
- Perform the PCM Verification Test. Powertrain Verification Test

No

- Replace the Throttle Body.
- Perform the PCM Verification Test. Powertrain Verification Test

7. POWERTRAIN CONTROL MODULE (PCM)
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors between the MAP Sensor and the Powertrain Control Module (PCM) and between the Throttle Body and the Powertrain Control Module (PCM).
Look for any chafed, pierced, pinched, or partially broken wires.
Look for broken, bent, pushed out or corroded terminals.
Search for any Technical Service Bulletins that may apply.
Were any problems found?

Yes

- Repair as necessary.
- Perform the PCM Verification Test. Powertrain Verification Test

No

- Replace and program the Powertrain Control Module (PCM).
- Perform the PCM Verification Test. Powertrain Verification Test

pro multis Credits:Operation CHARM About Operation CHARM