P0658

DTC P0658 or P0659

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.

* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P0658
- Solenoid High Control Circuit Group 1 Low Voltage

DTC P0659
- Solenoid High Control Circuit Group 1 High Voltage

Circuit/System Description

The transmission control module (TCM) high side driver 1 is located inside of the control solenoid valve assembly, which has no serviceable components. The high side driver 1 provides power to the pressure control solenoids and shift solenoids.

Conditions for Running the DTC

P0658

* DTC P0658 is not set.

* High side driver 1 is enabled.

P0659

* DTC P0659 is not set.

* Ignition transitions from OFF to ON

Conditions for Setting the DTC

P0658

TCM detects an internal open or short to ground in the high side driver 1 circuit for 1 s.

P0659

TCM detects an internal short to voltage on the high side driver 1 for 1 s.

Action Taken When the DTC Sets

P0658

* DTC P0658 is a Type A DTC.

* TCM turns the high side driver OFF.

* TCM turns OFF all solenoids.

* TCM commands maximum line pressure.

* TCM freezes transmission adaptive functions.

* TCM commands the torque converter clutch (TCC) OFF.

* TCM inhibits Tap Up/Down function.

* TCM inhibits manual shifting of forward gears.

* TCM limits the transmission to Reverse and 5th gear operation.

* TCM requests a reduced torque value based on input speed.

P0659

DTC P0659 is a Type C DTC.

Conditions for Clearing the DTC

* DTC P0658 is a Type A DTC.

* DTC P0659 is a Type C DTC.

Reference Information

Schematic Reference

Automatic Transmission Controls Schematics Electrical Diagrams

Connector End View Reference

* Component Connector End Views A/C Compressor Clutch

* Inline Harness Connector End Views X100

Description and Operation

* Transmission General Description Transmission General Description

* Transmission Component and System Description Transmission Component and System Description

* Electronic Component Description Electronic Component Description

Electrical Information Reference

* Circuit Testing Circuit Testing

* Connector Repairs Connector Repairs

* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections

* Wiring Repairs Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References Control Module References for scan tool information

Special Tools

DT-47825-20 - Adapter Harness

For equivalent regional tools, refer to Special Tools Tools and Equipment.

Circuit/System Verification

1. Ignition ON.

2. Verify the scan tool High Side Driver 1 parameter displays ON.

• If ON is not displayed

Refer to Circuit/System Testing.

• If ON is displayed

3. Engine Running, and transmission in Park.

4. Verify the scan tool parameters listed below do not display Malfunction:

* High Side Driver 1 Circuit Low Voltage Test Status

* High Side Driver 1 Circuit Open Test Status

* High Side Driver 1 Circuit High Voltage Test Status

• If Malfunction is displayed
Refer to Circuit/System Testing.

• If Malfunction is not displayed

5. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

6. Verify the DTC does not set.

• If the DTC sets
Refer to Circuit/System Testing.

• If the DTC does not set

7. All OK.

Circuit/System Testing

Note: You must perform the Circuit/System Verification first.

1. Ignition OFF, remove the Q8 Control Solenoid Valve Assembly.

2. Verify the Q8 Control Solenoid Valve Assembly is not contaminated with any debris. Refer to Control Solenoid Valve and Transmission Control Module Assembly Inspection Control Solenoid Valve and Transmission Control Module Assembly Inspection

• If contaminated
Repair as necessary

• If not contaminated

3. Verify the resistance is within the specified range for each solenoid listed in the Control Solenoid Valve and Transmission Control Module Assembly Inspection Control Solenoid Valve and Transmission Control Module Assembly Inspection.

• If the resistance is not within range
Replace the Q8 Control Solenoid Valve Assembly.

• If the resistance is within range

4. Place the Q8 Control Solenoid Valve Assembly on a clean work surface near the transmission assembly.

5. Connect the DT 47825-20 - adapter harness between the vehicle wire harness electrical connector and the Q8 Control Solenoid Valve Assembly electrical connector. Ignition ON.

6. Verify the scan tool parameters listed below do not display Malfunction:

* High Side Driver 1 Circuit Low Voltage Test Status

* High Side Driver 1 Circuit Open Test Status

* High Side Driver 1 Circuit High Voltage Test Status

• If Malfunction is displayed

Replace the Q8 Control Solenoid Valve Assembly.

• If Malfunction is not displayed

7. All OK.

Repair Instructions

Perform the Diagnostic Repair Verification Verification Tests after completing the repairs.

* Perform the Reset Transmission Adapts Reset Procedure following all transmission repairs.

* Control Module References Control Module References for Control Solenoid Valve Assembly replacement, programming, and setup.