FREE REPAIR MANUALS & LABOR GUIDES 1982-2013 Vehicles
Courtesy of Operation CHARM: Car repair manuals for everyone.
Home >> Chevy Truck >> 2012 >> Express 3500 V8-6.6L DSL Turbo >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> P Code Charts >> P24A1

P24A1




DTC P144B, P144C, P24A0, or P24A1

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.

* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P144B

-
Closed Loop Diesel Particulate Filter (DPF) Regeneration Control At Limit - Stage 1 Temperature Too Low

DTC P144C

-
Closed Loop Diesel Particulate Filter (DPF) Regeneration Control At Limit - Stage 1 Temperature Too High

DTC P24A0

-
Closed Loop Diesel Particulate Filter (DPF) Regeneration Control At Limit - Temperature Too Low

DTC P24A1

-
Closed Loop Diesel Particulate Filter (DPF) Regeneration Control At Limit - Temperature Too High

Circuit/System Description

The particulates in the exhaust gases are collected by the diesel particulate filter (DPF). When the filter becomes saturated with particulates, they are oxidized by a regeneration process. The regeneration process increases the exhaust gas temperature, heating the diesel oxidation catalyst (DOC), and the DPF. The accumulated particulate matter in the DPF will then be safely converted to harmless gases and the DPF will then be clean and ready to filter additional particulate matter.

The engine control module (ECM) monitors the system with inputs from the exhaust gas temperature (EGT) sensors and a differential pressure sensor. This diesel particulate filter diagnostic provides a means for monitoring the exhaust particulate filter efficiency. The resistive exhaust flow is monitored to determine if a DPF substrate is missing or a defined DPF failure has occurred. The resistive exhaust flow is calculated from mass air flow and DPF differential pressure. This diagnostic will run after a successful regeneration event has completed. This includes a successful service regeneration event.

Conditions for Running the DTC

P144B or P144C

* DTCs P0101, P0102, P0103, P0420, P10CD, P202E, P20CB, P20CD, P2263,P2463, P2598, or P2599 are not set.

* The engine run time is greater than 10 s.

* The engine speed is greater than 900 RPM.

* The ignition voltage is greater than 11 V.

* The ECM is commanding a DPF regeneration.

* The vehicle speed is a steady 89 km/h(55 mph).

* The exhaust temperature sensor 1 is between 100-650°C (212-1,200°F).

* The exhaust temperature sensor 1 and 4 is less than 650°C (1,200°F).

* The DTCs run continuously once the above conditions are met for 15 minutes.

P24A0 or P24A1

* DTCs P0101, P0102, P0103, P0420, P10CD, P202E, P20CB, P20CD, P2263,P2463, P2598, or P2599 are not set.

* The engine run time is greater than 10 s.

* The engine speed is greater than 900 RPM.

* The ECM is commanding a DPF regeneration.

* The vehicle speed is between 24-200 km/h (15-124 mph).

* The exhaust temperature sensor 1 and 4 is greater than 230°C (446°F).

* The exhaust temperature sensor 1 and 4 is less than 750°C (1,382°F).

* The DTCs run continuously once the above conditions are met for 10 minutes.

Conditions for Setting the DTC

The exhaust gas temperature is less than or greater than the calibrated desired temperature.

Action Taken When the DTC Sets

DTCs P144B, P144C, P24A0, and P24A1 are Type B DTCs.

Conditions for Clearing the DTC

DTCs P144B, P144C, P24A0, and P24A1 are Type B DTCs.

Diagnostic Aids

* If the engine has sat overnight, both EGT sensors and the ECT sensor values should display within 3°C (5°F).

* After starting a cold engine, the EGT sensor temperatures should rise steadily, then stabilize.

* An EGT sensor circuit with high resistance could set a DTC.

Reference Information

Schematic Reference

Engine Controls Schematics [1][2]Electrical Diagrams

Connector End View Reference

Component Connector End Views 1-2 Shift Solenoid (SS) Valve (M30)

Description and Operation Reference

Exhaust Aftertreatment System Description Emission Control Systems

Electrical Information Reference

* Circuit Testing Circuit Testing

* Connector Repairs Connector Repairs

* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections

* Wiring Repairs Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References Control Module References for scan tool information

Circuit/System Verification

1. Ignition On, observe the DTC information with a scan tool. Verify no other DTCs are set.

• If any other DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle Diagnostic Trouble Code (DTC) List - Vehicle for further diagnosis.

2. Measure and record the resistance of the B131 exhaust gas temperature sensor 1 and 2. Compare the measurements to the Temperature Versus Resistance (Fuel Temperature Sensor) Temperature Versus Resistance (Fuel Temperature Sensor)Temperature Versus Resistance (IAT Sensor 1) Temperature Versus Resistance (IAT Sensor 1)Temperature Versus Resistance (EGT Sensors) Temperature Versus Resistance (EGT Sensors)Temperature Versus Resistance (IAT Sensor 2) Temperature Versus Resistance (IAT Sensor 2)Temperature Versus Resistance (ECT Sensors) Temperature Versus Resistance (ECT Sensors)Temperature Versus Resistance (EGR Temperature Sensors) Temperature Versus Resistance (EGR Temperature Sensors) table. The resistance values should be within the specified range indicated in the table.

• If not within the specified range, replace the appropriate exhaust gas temperature sensor.

3. Inspect for the following conditions:

* Intake system for leaks or restrictions. Perform the Induction System Smoke Test in Charge Air Cooler Diagnosis (Full System Air Leak Test) Charge Air Cooler Diagnosis (Full System Air Leak Test)Charge Air Cooler Diagnosis (Induction System Smoke Test) Charge Air Cooler Diagnosis (Induction System Smoke Test).

* Exhaust system for leaks or restrictions-Refer to Symptoms - Engine Exhaust Symptoms - Engine Exhaust.

* Fuel system for leaks or restrictions

* Q57 Indirect fuel injector leaking or restricted-Refer to Indirect Fuel Injector Diagnosis Component Tests and General Diagnostics

* Excessive water in fuel-Refer to Contaminants-in-Fuel Diagnosis Contaminants-in-Fuel Diagnosis.

* EGR for normal operation

* Plugged fuel filter

* Restricted air filter

* Turbocharger for normal operation

* An engine mechanical condition

• If a condition is found, repair as necessary.

4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Repair Instructions

* Exhaust Temperature Sensor Replacement - Position 1 Exhaust Temperature Sensor Replacement - Position 1

* Exhaust Temperature Sensor Replacement - Position 2 Exhaust Temperature Sensor Replacement - Position 2

Repair Verification

1. Install any components or connectors that have been removed or replaced during diagnosis.

2. Perform any adjustment, programming, or setup procedures that are required when a component or module is removed or replaced.

3. Clear the DTCs.

4. Ignition OFF, all vehicle systems OFF, this may take up to 2 minutes.

5. Perform the scan tool Diesel Particulate Filter (DPF) Regeneration Enable Diesel Particulate Filter (DPF) Regeneration Enable.

6. Engine idling at operating temperature. Accelerate at part throttle to 48 km/h (30 mph) with this speed maintained until all Conditions for Running the DTC are met. The DTCs should not set.

pro multis Credits:Operation CHARM About Operation CHARM