P0202

DTC P0201, P0202, P0203, P0204, P0205, P0206, P0207, or P0208

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. Initial Inspection and Diagnostic Overview
* Review Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P0201
- Fuel Injector 1 Control Circuit

DTC P0202
- Fuel Injector 2 Control Circuit

DTC P0203
- Fuel Injector 3 Control Circuit

DTC P0204
- Fuel Injector 4 Control Circuit

DTC P0205
- Fuel Injector 5 Control Circuit

DTC P0206
- Fuel Injector 6 Control Circuit

DTC P0207
- Fuel Injector 7 Control Circuit

DTC P0208
- Fuel Injector 8 Control Circuit

Diagnostic Fault Information






Circuit/System Description

The engine control module (ECM) supplies voltage to each fuel injector on the injector positive voltage control circuits. The ECM energizes each fuel injector by grounding the control circuit of that fuel injector. The ECM monitors the status of the injector positive voltage control circuits and the fuel injector control circuits. The injectors are separated into the following four groups:

* Group 1-DTC P2146 with injectors 1 and 4
* Group 2-DTC P2149 with injectors 6 and 7
* Group 3-DTC P2152 with injectors 2 and 5
* Group 4-DTC P2155 with injectors 3 and 8

When a fuel injector circuit condition is detected by the ECM, the affected fuel injectors will be disabled and may disable the affected group of fuel injectors.

Conditions for Running the DTC

* The engine is running.
* The charging system voltage is between 10-18 volts.

Conditions for Setting the DTC

* The ECM injector output driver detects an incorrect current on a fuel injector circuit.
* The condition exists for 1 second.

Action Taken When the DTC Sets

DTCs P0201, P0202, P0203, P0204, P0205, P0206, P0207, and P0208 are Type A DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0201, P0202, P0203, P0204, P0205, P0206, P0207, and P0208 are Type A DTCs.

Circuit/System Testing

Important: If you cannot duplicate the condition, operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Observe the DTC information with a scan tool. If DTC P2146, P2149, P2152 or P2155 are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle. Diagnostic Trouble Code Descriptions

One Fuel Injector DTC Sets
1. Test the affected fuel injector control circuit for an open between the ECM and the fuel injector.
2. Test the affected fuel injector for high resistance.

^ If the circuit and fuel injector test normal, replace the ECM.

Two or More Fuel Injector DTCs Set
1. Test the affected fuel injector circuit for an following:

* An open between the ignition position voltage control circuit splice and the fuel injector connector
* An open between the ECM and the ignition positive voltage control circuit splice

2. Test the affected fuel injector for high resistance.

^ If the circuit and fuel injector test normal, replace the ECM.

Component Testing

1. Disconnect the connector of the fuel injector to be tested.
2. Connect a DMM between the terminals of the fuel injector and measure the resistance. The resistance should be 0.2-0.3 ohms.

^ If the resistance is more than 0.2-0.3 ohms resistance, replace the fuel injector.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure. Verification Tests

* Fuel Injector Replacement (Left) Fuel Injector Replacement (Right)