Programming Features

ENTER PROGRAMMING MODE
Perform the following steps in order to enter the programming mode:
1. Turn IP dimmer switch All the way to the right then back slightly to the left.
2. With the ignition in the OFF position, remove the BCM PRGRM fuse.
3. Turn the ignition to the ACC position.
4. Listen to the number of chimes. The chimes indicate the BCM type (2, 3, or 4) and therefore the features that may be personalized.

AUTOMATIC DOOR LOCKS
Continue with the following steps in order to personalize the automatic door locks:
1. Press and release the any power door lock switch. Count the number of chimes in order to determine the current mode.
2. Press any power door lock switch again in order to advance to the next mode. The chime will sound the number of times equivalent to the mode.
3. Continue to press any power door lock switch until you reach the desired mode.

CONTENT THEFT DETERRENT
Continue with the following steps in order to personalize the content theft deterrent:
1. Cycle the park lamps (ON then OFF). Count the number of chimes in order to determine the current mode.
2. Cycle the park lamps again in order to advance to the next mode. The chime will sound the number of times equivalent to the mode.
3. Continue to cycle the park lamps until you reach the desired mode.

CONTENT THEFT DETERRENT ARMING/DISARMING
Continue with the following steps in order to personalize the content theft deterrent arming/disarming:
1. Insert a second key into any door lock cylinder.
2. Rotate the key to the UNLOCK position and hold for 1 second. Count the number of chimes in order to determine the current mode.
3. Rotate the key again or press the Panic button on vehicles equipped with keyless entry in order to advance to the next mode. The chime will sound the number of times equivalent to the mode.
4. Continue to rotate the key or press the Panic button until you reach the desired mode.
5. Remove the key from the door lock cylinder.

DELAYED ILLUMINATION AND EXIT LIGHTING
Continue with the following steps in order to personalize the delayed illumination and the exit lighting features:
1. Turn the courtesy lamps on by turning the instrument panel brightness control all the way to the DOME position. Count the number of chimes in order to determine the current mode.
2. Turn the courtesy lamps to the DOME position again in order to advance to the next mode. The chime will sound the number of times equivalent to the mode.
3. Continue to cycle the courtesy lamps until you reach the desired mode.

DELAYED LOCKING AND LOCKOUT PREVENTION
Continue with the following steps in order to personalize the delayed locking and the lockout prevention features:
1. Press the power door unlock switch. Count the number of chimes in order to determine the current mode.
2. Press the power door unlock switch again in order to advance to the next mode. The chime will sound the number of times equivalent to the mode.
3. Continue to press the power door unlock switch until you reach the desired mode.

REMOTE ACTIVATION VERIFICATION (IF EQUIPPED WITH KEYLESS ENTRY)
Continue with the following steps in order to personalize the remote activation verification for the remote keyless entry:
1. Press the LOCK button on the keyless entry transmitter. Count the number of chimes in order to determine the current mode.
2. Press the LOCK button on the transmitter again in order to advance to the next mode. The chime will sound the number of times equivalent to the mode.
3. Continue to press the LOCK button until you reach the desired mode.

REMOTE UNLOCK CONTROL (IF EQUIPPED WITH KEYLESS ENTRY)
Continue with the following steps in order to personalize the remote unlock control for the remote keyless entry:
1. Press the UNLOCK button on the keyless entry transmitter. Count the number of chimes in order to determine the current mode.
2. Press the UNLOCK button on the transmitter again in order to advance to the next mode. The chime will sound the number of times equivalent to the mode.
3. Continue to press the UNLOCK button until you reach the desired mode.

EXIT PROGRAMMING
Continue with the following steps in order to exit the programming mode:
1. Turn the ignition to the OFF position.
2. Replace the BCM PRGRM fuse.

ADDITIONAL INFORMATION
For more information about the personalization features, refer to one of the following description and operations:
^ Refer to Content Theft Deterrent (CTD) Description and Operation in Theft Deterrent for more information about the following features:
^ Content theft deterrent arming method
^ Content theft deterrent arming verification
^ Refer to Power Door Locks Description and Operation in Doors for more information about the following features:
^ Delayed locking
^ Lockout prevention
^ Refer to Interior Lighting Systems Description and Operation in Lighting for more information about the following features:
^ Delayed illumination
^ Exit lighting
^ Refer to Keyless Entry System Description and Operation in Keyless Entry for more information about the following features:
^ Remote activation verification
^ Remote unlock control.