P2303

DTC P2300, P2301, P2303, P2304, P2306, P2307, P2309, or P2310

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.

DTC Descriptors
DTC P2300
- Ignition Coil 1 Control Circuit Low Voltage

DTC P2301
- Ignition Coil 1 Control Circuit High Voltage

DTC P2303
- Ignition Coil 2 Control Circuit Low Voltage

DTC P2304
- Ignition Coil 2 Control Circuit High Voltage

DTC P2306
- Ignition Coil 3 Control Circuit Low Voltage

DTC P2307
- Ignition Coil 3 Control Circuit High Voltage

DTC P2309
- Ignition Coil 4 Control Circuit Low Voltage

DTC P2310
- Ignition Coil 4 Control Circuit High Voltage

Diagnostic Fault Information





Circuit/System Description

The ignition system uses individual ignition coil/module assemblies for each cylinder. The engine control module (ECM) controls the individual coils by transmitting timing pulses on the ignition control (IC) circuit of each ignition coil/module to enable a spark event. When the engine is running the ECM monitors each IC circuit for improper voltage levels. Each ignition coil/module has the following circuits:

* Ignition voltage
* Ground
* IC
* Low reference

Conditions for Running the DTCs

* The engine speed is less than 6,000 RPM.
* The ignition 1 voltage signal is between 9-18 volts.
* DTCs P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310 run continuously when the above conditions are met.

Conditions for Setting the DTCs

* The ECM detects a short to ground on the circuit or the ignition coil/module for greater than 4 seconds continuously or 50 seconds cumulative.
OR
* The ECM detects a short to voltage on the circuit or the ignition coil/module for greater than 4 seconds continuously or 50 seconds cumulative.

Action Taken When the DTC Sets

DTCs P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310 are Type B DTCs.

Reference Information
Schematic Reference

Engine Controls Schematics ([1][2]Electrical Diagrams)
Connector End View Reference

Component Connector End Views (Connector Views)
Electrical Information Reference

* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Powertrain Diagnostic Trouble Code (DTC) Type Definitions)
Scan Tool Reference

Control Module References (Programming and Relearning) for scan tool information

Circuit/System Verification

1. Start and idle the engine.
2. Observe the scan tool Misfire Current Cylinder parameters. The counters should not be incrementing.
3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Turn ON the ignition, with the engine OFF.
2. Test the affected IC circuit for a short to ground or for a short to voltage.

• If a fault is found, repair the circuit as needed.

3. Ignition OFF, exchange the affected ignition coil/module with the ignition/coil module of a good cylinder.
4. Start the engine and observe the scan tool.

• If the DTC or the misfire transfers with the suspect ignition/coil module, replace as needed.
• If the DTC or the misfire does not transfer with the suspect ignition/coil module, replace the ECM.

Repair Instructions

* Ignition Coil Replacement (Service and Repair)
* Control Module References (Programming and Relearning) for ECM replacement, setup, and programming

Repair Verification

If the customer concern was a flashing MIL, then perform the following procedure:

1. Install any components that have been removed or replaced during diagnosis.
2. Perform any adjustments, programming or setup procedures that are required when a component is removed or replaced.
3. Clear the DTCs.
4. Turn OFF the ignition for 60 seconds.
5. If the repair was related to a DTC, duplicate the Conditions for Running the DTC and use the Freeze Frame/Failure Records, if applicable, in order to verify the DTC does not reset. If the DTC resets or another DTC is present, refer to the Diagnostic Trouble Code (DTC) List - Vehicle (Diagnostic Trouble Code (DTC) List - Vehicle) and perform the appropriate diagnostic procedure.
6. To verify that the performance of the catalytic converter has not been affected by the condition that set this DTC, perform the Repair Verification for DTC P0420. Refer to DTC P0420 (P0420).